ADS-127 Final Polishing Film

5 inch Disc; Silicon Dioxide; Ceramic Ferrule; no PSAADS-NEXT polishing films feature stable polishing force while maintaining final finish performance and achieving an extended life-span. This series of final polishing films attains a high-performance polish with distilled water. Another feature of the ADS-NEXT series is a sharp improvement in the indentation problems that occur especially in 1.25 mm diameter ferrules from repeated use polishing. Even after many usages, ADS-NEXT can still protect against sudden occurrences of fiber indentation.

Cleaning Tools for Optics;NEOCLEAN;Simple Type;Single-core; Multi-core;MU; LC; SC; FC; ST; MT; MPO; MTRJ;Number of Cleaning: 400 times or more; Packing Quantity: 5 pcs/set;

5 inch Disc; Grit 0.3 µm; Aluminium Oxide; Stainless Steel Ferrule; no PSA The 26M-0.3-5D fiber optics polishing film from Nanolap comes in a pack that contains 10 pieces.

High Speed; Fiber Type SM, PM, RC; 780-1625 nm; Fiber Length 5-17 m; Fiber Stretch 0.035-0.21 µm/V; Fiber Leads 1 m, 0.9 mm OD Jacket; Connector Type Bare Fiber, FC/PC, FC/APC The PZ1 series are the high-speed members of Optiphase’s family of fiber stretchers. At the core of the PZ1 high-speed fiber stretchers is a fiber wound piezoelectric element for use in a wide range of optical interferometric measurement and sensing system applications. Optiphase’s expertise in the design, manufacture and use of all-fiber interferometers has produced a unique multi-layer winding approach resulting in an enhanced modulation function while maintaining a high operational frequency. PZ1 high-speed fiber stretchers are available with single mode (SM), commercial polarization maintaining (PM, Panda or Bowtie) or SM reduced cladding (RC) fiber types PZ1 high-speed fiber stretchers deliver a high performance to cost ratio, exceeding all other known competitive devices. The compact and low-profile form factor makes the PZ1 series easily configurable into small spaces. In addition, Optiphase fiber stretchers are unique in that they do not require proprietary drivers. For most low-voltage applications (<±15 V), Optiphase stretchers can be driven by standard electronics such as signal generators, op-amps or other laboratory equipment without modification. For more information on how to drive PZ1 high-speed fiber stretchers see the downloadable application note. Key Features: High Speed Compact Package Fiber Type: Single Mode (SM), Polarization Maintaining (PM )or Reduced Cladding SM (RC) Fiber Multiple Termination Choices Unique Multi-layer Winding Can Be Driven With General Purpose Electronics Operational Wavelength: 780 to 1625 nm Fiber Stretch: 0.035 to 0.21 µm/V Optical Path Displacement (n = 1): 0.05, 0.2, 0.3 µm/V Time Delay: 0.00017 to 0.001 ps/V Fiber Length: 5, 12.3, 17 m Inclusive Fiber Wind: 4 Layer (1 Layer PM Version Available) Optical Loss: ≤0.5 dB Maximum Voltage Range: ±500 V (Off Resonance, 1,000 V Peak-to-Peak) Fiber Leads: 1 m, 900 μm Loose Tube Connector Type: Bare Fiber, FC/PC, FC/APC Dimensions: 50.8 x 50.8 x 21.6 mm Applications: Open Loop Demodulation; Sensor Simulation; Variable Optical Delay; General Purpose Fiber Interferometry; Large-angle Modulation of Interferometric Phase

5 inch Disc; Silicon Dioxide; Ceramic Ferrule; no PSA The ADS film can be used for final polishing for optical fiber connector end-face. The ADS film offers longer life cycle for the optical connector polishing. NTT Advanced Technology’s ADS series of final polishing films is ideal for the final polish of optical connector end faces and offers longer polishing life cycles. These films polish the end face of an optical connector without scratches, residues or contamination on the ferrule end face. ADS-NEXT polishing films feature stable polishing force while maintaining final finish performance and achieving an extended life-span. This series of final polishing films attains a high-performance polish with distilled water. Another feature of the ADS-NEXT series is a sharp improvement in the indentation problems that occur especially in 1.25 mm diameter ferrules from repeated use polishing. Even after many usages, ADS-NEXT can still protect against sudden occurrences of fiber indentation. ADS-MPO series is a new generation of polishing films that has been improved for MPO connector end faces to realize a finishing quality equivalent to that of single fiber polish, leaving no scratches or dirt while at the same time their stable polishing power ensures long life. These films can polish to a convex shape to eliminate dips in the core (Coredip value of “0”) which particularly affects the optical characteristics (IL/RL) of multi mode fiber. APS-MPO final polishing films also realize low return loss, comparable to single connectors, by suppressing subsurface damaged layer to a minimum. With a base thickness of 75 µm, they are available in disc and sheet types. Key Features: Ideal for Final Polish of MPO Optical Connector End Face High Stability and Long Product Lifetime Prevents Excessive Fiber Undercut after Repeated Use (ADS/ADS-NEXT) Multi Mode Fiber Coredip Value of “0” (ADS-MPO) Low Return Loss Comparable to Single Mode Fiber Connectors (ADS-MPO) Compatible with 1.25, 2.5 mm Diameter Zirconia Ferrules (ADS/ADS-NEXT), MPO Ferrule, All Types (ADS-MPO) Compatible with Multi Mode (OM1/2/3/4, GI50/62.5, etc.) and Single Mode (OS1/2, SM, etc.) Fiber (ADS-MPO) Disc Type (5.0 inch, 127 mm Diameter), Sheet Type (5.5 x 5.5 inch, 140 x 140 mm, ADS-MPO) and Roll Type (5.5 inch, 140 mm x 12 m, ADS/ADS-NEXT) Available Applications: Final Polish of Fiber Connector End Face

Cleaning Tools for Optics;CLETOP;Stick Type;Video;HDTV;; Packing Quantity: 100 sticks/ set;