Beamsplitters and Dichroic Filters

Input Voltage 187-460 VAC 3-Phase; Max. Output Voltage 1-150 kVDC; Max. Power 5,000 W; Efficiency >85%; Voltage Regulation <0.005%-<0.025%; Current Regulation <0.2%, <0.5% XP Glassman’s LH Series are sophisticated 5 kW high voltage AC/DC power supplies with low ripple and noise. They are air insulated, fast response, 6U rack-mount units with tight regulation. A broad range of models is available with output voltage ranges from 0 to 1 kVDC through 0 to 150 kVDC. The LH Series features “air” as the primary dielectric medium. No oil or encapsulation is used to impede serviceability or increase weight. Internal circuitry constantly senses and integrates arcs that occur over a given time. In the event a system or load arcing problem develops and exceeds factory-set parameters, the power supply will cycle off in an attempt to clear the fault and then automatically restart after a preset “off dwell time”. The LH Series’ high voltage output is inhibited for a short period after each load arc to help extinguish the arc. Typically, ripple is less than 0.05% RMS of rated voltage at full load. Off-the-line pulse-width modulation (PWM) provides high efficiency and a reduced parts count for improved reliability. The LH Series’ front panel contains all local control functions like AC power on/off, separate 10-turn controls to set voltage and current levels, HV voltage on and off/reset switches as well as LED indicators for high voltage on, output polarity, interlock, fault status or voltage/current regulating mode. Output levels are indicated by voltage and current digital meters. All voltage and current programming and monitoring signals are coupled to the user interface by true differential amplifiers. This provides for the ability to return the program and monitor commons to ground or system common at the source. This arrangement isolates the return wires and eliminates errors due to unwanted return currents flowing in these connections. The LH Series’ standard operation mode is constant voltage/current. Automatic crossover from constant-voltage to constant-current regulation provides protection against overloads, arcs and short circuits. A rear panel switch allows selection of either constant-current or current-trip operation. Thermostats and fan RPM sensing shut down the power supply due to over-temperature or reduced fan speeds. Standard accessories for the LH Series include a remote interface mating connector and a detachable 2,4 m shielded high voltage coaxial output cable. The LH Series supplies, when configures with the 400 VAC input option, are fully compliant with the following European harmonized EMI directives: EN61010/ IEC61010, Safety EN61000-6-4, Conducted and Radiated Emissions EN61000-6-2:2005, Conducted and Radiated Immunity 2011/65/EU, Restriction of the Use of Hazardous Substances (RoHS) Key Features: 6U Rack Mount Air Insulated Maximum Output Power: 5 kW – Parallelable to 25 kW Maximum Output Voltage: 1 to 150 kVDC Maximum Output Current: 25 mA to 5.0 A Low Ripple: <0.05% RMS of Rated Voltage at Full Load Tight Regulation Static Voltage Regulation: <0.005% for Specified Line and 0.01% for Specified Load Variations, 0.025% for 80 to 100 kVDC Models Current Regulation: <0.2% (8 to 150 kV), <0.5% (1 to 6 kV) From Short Circuit to Rated Voltage at Any Load Condition Constant Voltage/Constant Current Operation Arc Quench & Arc Count Front Panel, Remote, RS232, USB & Optional Ethernet Control Input Voltage: 187 to 228 or 340 to 460 VAC RMS, 48 to 63 Hz, Three Phase Efficiency: >85% Typical at Full Load Output Voltage Accuracy: 0.5% of Setting + 0.2% of Rated Stored Energy: 3.5 to 58 J Voltage Monitor: 0 to +10 VDC Signal for 0 to Rated Voltage Current Monitor: 0 to +10 VDC Signal for 0 to Rated Current Stability: 0.01%/h After 0.5 h Warm-up, 0.05% per 8 h Polarity: Positive, Negative or Reversible Polarity With Respect to Chassis Ground Protection: Against All Overload Conditions, Including Arcs and Short Circuits Signals Provided on the Remote Interface Connector: Differential Voltage & Current Program/Monitor, HV Enable/Status, Safety Interlock, Fault Status, +10 V Reference, I/V Mode Status Options: Blank Front Panel, Zero Start Interlock, Slow Start Ramp, 0 to 5 V Voltage & Current Program/Monitor, Arc Count and Quench, Common to Ground Isolation, Control and Monitor via RS232, USB, Ethernet 3 Year Warranty Approvals: IEC61010-1:2010; EN61000-6-4:2007, Class A EN61000-6-2:2005 Operating Temperature: -20 to +40 °C Dimensions: 265.9 x 482.6 x 609.6 mm Applications: High Voltage, High Power Applications; Photonics; Healthcare (Analytical, Diagnostics, Detectors); Industrial; Semiconductor Manufacturing; Research; Other

Material Synthetic, Tissue, Aluminium Composite, Steel Sheets, Special Laser Protective; Thickness 0.8-100 mm; Max. Power Density 100 W/ m2-25 MW/m2 for 100 s Our broad portfolio of PROTECT-Laserschutz laser safety curtains and laser safety cabins for different applications allows you to find the appropriate large area laser protection solution for your laser. All safety materials are tested and certified according to EN 12254. In order to provide the maximum level of protection for employees it is necessary to choose the appropriate safety material for protection of large areas against laser radiation. Several laser parameters such as the wavelength, the laser power and the mode of operation are considered for protection level calculations. Please carefully calculate the required safety levels for your laser - for advice how to choose the right large area laser protection solution for your application, get in touch with the AMS Technologies laser safety experts now. isoPROTECT-Budget, isoPROTECT-Budget LP, isoPROTECT-Budget-Extra, and isoPROTECT-Budget Superior laser safety curtains for low-power applications protect against scattered radiation as well as direct radiation. Due to in-house production, all dimensions are available (as far as technically possible). Made from synthetic material with thicknesses of approximately 0.8, 0.85, 1.6 and 2.8 mm, these laser safety curtains allow maximum power densities of 100 W/m2 to 2.5 MW/m2 for 100 s. In addition, individual wishes such as velcro, hem and eyelet tape are possible on request. Standard colour is Carbon/Carbon and for larger quantities a choice from a variety of other colours is available. isoPROTECT Service, a mobile large area laser safety barrier, is made from isoPROTECT-Budget black synthetic material with 0.8 mm thickness. The standard version consists of three individual panels (2 x 1 m each) that can be connected by Velcro. These panels are arbitrarily extendable, can be easily mounted based on aluminium frames and the transport in the included storage bag is comfortable. The isoPROTECT High Tech laser safety curtain provides highest possible protection levels for applications with the danger of direct radiation. Due to in-house production, all dimensions are available (as far as technically possible). If larger surfaces are needed, this curtain can be easily expanded thanks to velcro tape. Made from tissue with a thickness of approximately 2.0 mm, this laser safety curtain allows maximum power densities of 1 to 25 MW/m2 for 100 s. Coating is available in black and white. As one of the leading manufacturers of laser protection cabins, PROTECT-Laserschutz is familiar with the customers’ specific requirements of laser protection cabins. PROMETHEUS and HERCULES laser safety cabins are designed in accordance to individual specifications and customized to the user's specific laser system. Get in touch with the AMS Technologies laser safety experts now to discuss your customized laser protection cabin solution. While PROMETHEUS laser cabins made of Aluminium Composite material with 4 mm thickness allow maximum power densities of 10 to 250 MW/m2 for 100 s, HERCULES laser safety cabins made of steel sheets and special laser protective material with 100 mm thickness allow maximum power densities of 10 to 2500 MW/m2 for 100 s. Experienced and reliable installation partners can promptly install PROTECT-Laserschutz protection cabins on-site. On request, we are glad to perform a risk analysis at your company, so that your cabin can be used in conformity with EN 60825-4 and be classified as laser class 1. Certified according to EN ISO 13849-1, the LSK10 laser safety control system for entrance doors to cabins allow active controlling of laser applications by interlock contacts, by power supply or by beam dumps. There are various input types for integration of mechanical/magnetic door contacts, warning lights, emergency stops, laser safety roller blinds and curtains. Key Features: Laser Safety Curtain Material: Synthetic, Tissue Laser Safety Curtain Thickness: 0.8 to 2.8 mm Laser Safety Curtain Maximum Power Densities: 100 W/m2 to 25 MW/m2 for 100 s, Depending on Laser Wavelength Laser Safety Cabin Material: Aluminium Composite, Steel Sheets and Special Laser Protective Laser Safety Cabin Thickness: 4, 100 mm Laser Safety Cabin Maximum Power Densities: 10 to 2500 MW/m2 for 100 s, Depending on Laser Wavelength Applications: Protection of Large Areas Against Potentially Dangerous Radiation Emitted by Common Laser Types