BG-HEDFA High-Power EDFA

Super-fast, Auto Gain Controlled; Fiber Pigtail 9/125 µm; 1529.16-1558.58 nm; Input Power -19--11 dBm; Output Power 5-13 dBm OZ Optics’ super-fast Erbium-doped fiber amplifier module EDFA-11-9/125 was developed to address fast transient conditions with sub-μs suppression time. In a WDM transmission line, the addition or removal of channels may cause a transient, to which the EDFA must respond. In response to a sudden change of input power, an EDFA will exhibit transient response, i.e. overshoot or undershoot in its output signal. With a typical EDFA, this transient response can last on the order of 100 μs. OZ Optics’ super-fast Erbium-doped fiber amplifier module EDFA-11-9/125 features a typical transient suppression time of 50 ns and is designed to be used in the traditional C-band. During operation, the signal wavelengths must be confined to a 3.2 nm region for each optical amplifier, although the band may be anywhere within the C-band. The unit can work with up to four channels. Due to the nature of the narrowband operation, the transient suppression of the super-fast EDFA module is greatly improved, compared to a traditional EDFA. Key Features: Compact Design Super-fast, Auto Gain Controlled Operation Wavelength: 1529.16 nm to 1558.58 nm Input Power per Channel: -19 dBm to -11 dBm Output Power per Channel: 5 dBm to 13 dBm Sub-μs Transient Suppression Time: 50 ns Typ. Transient Undershoot/Overshoot: ≤±0.3 dB Auto Gain Control Over Wavelength and Signal Amplitude Low Noise: 5.5 dB Fixed 24 dB Gain, Independent of Wavelength and Signal Power Gain Flatness Within 3.2 nm Band (Relative to 24 dB): ±0.3 dB Polarization Dependent Gain: ≤0.3 dB Max. Polarization Mode Dispersion: 0.5 ps/√km Input/Output Return Loss (RL): 40 dB Residual Pump Power at Output: -25 dBm Fiber Pigtail: 9/125 µm, 1 m Length Connector Type: FC/APC Operating Temperature Range: 0°C to +70°C Dimensions: 90 x 70 x 14 mm Applications: ROADM Network; CATV/NETWORK Access; C-Band Channel Preamp

CATV, Erbium-doped; Fiber Type SMF-28; 1530 to 1565 nm; Input Power -5 to +10 dBm; Output Power 13 to 23 dBm LightComm Technology’s 19" rack EDFA-CA-SO is designed for CATV long distance transmission, amplifying low signal power into high signal power or extending transmission distance. Both input and output signals are sampled and monitored with a feedback circuit. An APC (automatic power control) circuit is designed into the amplifier to ensure high stability and reliability of output power.Based on an integrated power monitoring circuit, this amplifier features Ethernet or RS-232 (or RS-485) network interface, capable to support open network management protocol (SNMP) as an option and adding flexibility to maintain connectivity with the customer's network management system.As an option, by using a select set of multi-channels splitters with extremely high reliability and low IL values, users can split the output signal into multiple ports. Key Features: Low Noise Figure High Output and High Gain Optional Output Configuration: 13 to 23 dBm (one output port), 17 dBm * 4 ports, 16 dBm *4 ports, 17 dBm *2 ports, 16 dBm *2 ports etc. Highly Reliable Laser Diode Pumps High Stability and Reliability Wide Operating Temperature Range Intelligent MPU Monitor User-friendly Interface RS232/RS485/SNMP (optional) Applications: Analog and Digital CATV Systems; Long Distance Transmission Systems; Access Networks; LANs and WANs

Mini Size, Erbium-doped; Fiber Type SMF-28e 900µm Jacket; 1530 to 1565 nm; Input Power -3 to +10 dBm; Output Power 15 to 17 dBm LightComm Technology’s EDFA-EM(-B) series of compact miniature size EDFA modules is designed for optical communication and CATV systems. Available in 20 dB (EDFA-EM-B) and 15 dB (EDFA-EM) versions, the series can be used as a power amplifier, in-line amplifier or pre-amplifier based on system architecture. It features stable output power, low noise and power consumption.Compact footprint makes it easy to be installed where it is needed, adding to flexibility in network design. To achieve high performance, world brand pump lasers and erbium-doped fibers are used; optical isolators are added at both input and output. Both input and output signals are sampled and monitored with a feedback circuit.APC (automatic power control), AGC (automatic gain control) and ACC (automatic current control) circuits are designed into the amplifier to ensure high output power stability and reliability. Based on integrated power monitoring circuits, this amplifier features a RS-232 interface, enabling connectivity to the customer’s control system. Key Features: Mini Size: 90×70×15 mm (EDFA-EM-B), 70×50×12 mm (EDFA-EM) High Output Power and High Gain Low Noise Figure Low Power Consumption Wide Operating Temperature Range Applications: Analog and Digital CATV Systems; Optical Communication Systems; LANs and WANs; In-line Amplification; DWDM Subsystems

Polarization Maintaining, Erbium-doped; Fiber Type SM15-PS-U25D; 1530 to 1565 nm; Input Power -10 to +10 dBm; Output Power 15 to 17 dBm LightComm Technology’s EDFA-PM-SO series of polarization maintaining fiber amplifiers is designed to output optimal optical performance with high reliability and stability. These amplifiers are especially developed for PM transmission, sensors and LIDAR applications. The EDFA-PM-SO line of PM fiber amplifiers features a single stage amplification configuration.The use of selected components with extremely high polarization extinction ratio and low insertion loss values, and the careful management of splice joints to preserve polarization. Both input and output signals are sampled and monitored with feedback circuit to protect the amplification system. APC (automatic power control), AGC (automatic gain control) and ACC (automatic current control) circuits are designed into the amplifier to ensure high stability and reliability of output power. Standard user-friendly Ethernet or RS-232 network interface enables reliable connectivity with the customer’s network management system. Key Features: High Polarization Extinction Ratio Low Noise Figure RS-232 or Ethernet Interface Highly Reliable Laser Diode Pumps High Stability and Reliability Based on Multi-mode Pump and PM Fiber Combining Technology Applications: LIDAR & Sensor; Test and Measurement; Coherent Synthesizing & Spectrum Synthesizing; Frequency Conversion; Microwave Optics; Booster Amplifier for PM Transmitters

Erbium-doped; 1530-1560 nm; Output Power ≥17 dBm; Signal Gain ≥25 dB; Return Loss -60 dB; Polarization Sensitivity 0.07 dB; Isolation 40 dB; Module or Instrument Form Factor Fibotec Fiberoptics’ Fibogain ERFA series of EDFA modules and instruments make use of the optical gain in an Erbium-doped fiber that is pumped by either 980 nm or 1480 nm light sources. Thus, incoming light of a longer wavelength in the C- or L-band is amplified and enhances the transmission span of fiber optic links. EDFAs typically operate in saturation, and the average power of a signal determines the average gain. Bit to bit dynamics or inter-channel crosstalk in DWDM-systems do not change the dynamics of an EDFA. This also enables the amplification of channel-bundles within the entire emission wavelength range of Erbium superimposing simple single-channel links. The average output power in both cases is determined by the saturation power of the specific EDFA design however. The majority of EDFAs is applied in fiberoptic links. Other applications can also be found - mainly in fiberoptic test & measurement setups and other instruments that include eye-safe free space measurement installations. Key Features: Remotely Controlled Instrument Module and Instrument Options Wavelength Range: 1530 nm to 1565 nm Minimum Output Power: 17 dBm (@0 dBm In) Minimum Signal Gain: 25 dB (@-10 dBm In) Noise Figure: 5 to 6 Polarization Sensitivity: 0.07 dB Isolation: 40 dB (Input & Output) Return Loss: -60 dB Loss of Signal <-25 dBm Pump Leakage: <-15 dBm (@980 nm) Customized Versions Available Dimensions: 145 x 100 x 17 mm (Module), 210 x 290 x95 mm (Instrument) Weight: <500 g (Module, < 4 kg (Instrument) Operating Temperature: 0°c to +40 °C (Non-condensing) Applications: Fiber Optic Links; Fiber Optic Test & Measurement Setups; Other Instruments That Include Eyesafe, Free-Space Measurement Installations

High Power, Yb/Er Co-doped; Fiber Type SMF-28(e); 1543 to 1565 nm; Input Power 0 (-10) to +10 dBm; Output Power -3 to +33 dBm LightComm Technology’s YEDFA-CA-EM-A/B/C series of Yb/Er co-doped high-power fiber amplifier modules are especially designed for FTTx, CATV, FDC and HFC analog amplification applications that require high reliability. Compared to conventional amplifiers, these modules are more compact, powerful, stable and reliable. Both input and output signals are sampled and monitored with a feedback circuit. ACC (automatic current control) and APC (automatic power control) circuits are designed into the amplifier to ensure high stability and reliability of output power. Based on integrated power monitoring circuit, this amplifier features RS-232 interface enabling connectivity with the customer’s control system.The YEDFA-CA-EM-A27 amplifier modules additionally features an AGC (automatic gain control) circuit as well as built-in EVOA to extend output power range to -3dBm, and the gain fiber is encased inside a hermetic sealed package.The YEDFA-CA-EM-C high power fiber amplifier modules are based on two stage amplification configuration, pre-amplifier and power amplifier. They additionally feature an AGC (automatic gain control) circuit. Key Features: Compact size: 90×70×25 mm (YEDFA-CA-EM-A), 125×100×25 mm (-B), 164×85×18 mm (-C) Wide Operating Temperature Range High Stability and Reliability Based on Multi-mode Pump and Fiber Combiner Technology RS-232 Interface Low Noise Figure Applications: Data Transmission; Power Actuator; Test/Measurement for Optical Devices and Systems; Detection for Gas Absorption; Analog CATV Long Distance Transmission Video; Optical Transmission Systems; Optical Distributing Systems; In-line Amplification; FTTx

Mini Size, High Power, Yb/Er Co-doped; Fiber Type SMF-28; 1543 to 1565 nm; Input Power 0 to +10 dBm; Output Power +27 dBm LightComm Technology’s YEDFA-CA-EM-B-27 series of miniature size, high power fiber amplifier modules is especially designed for FTTx, CATV, FDC and HFC analog amplification applications that require high reliability. Compared to conventional amplifiers, these modules are more compact, powerful, stable and reliable. Both input and output signals are sampled and monitored with a feedback circuit.Both ACC (automatic current control) and APC (automatic power control) circuits are designed into the amplifier to ensure high stability and reliability of output power. Based on integrated power monitoring circuits, this amplifier features a RS-232 interface, enabling connectivity to the customer’s control system. Key Features: Compact Size: 90×70×12 mm Wide Operating Temperature Range High Stability and Reliability Based on Multi-mode Pump and Fiber Combiner Technology RS-232 Interface Low Noise Figure Applications: Data Transmission; Power Actuator; Test/Measurement for Optical Devices/Systems; Detection for Gas Absorption; Analog CATV Long Distance Transmission; Optical Transmission Systems; Optical Distribution Systems; Inline Amplification; FTTx