Skip to main content

AMS-127-1.0-0.8 (30x30) HT120 E L2 69K Thermoelectric Cooler Qmax 56 W

Product information "AMS-127-1.0-0.8 (30x30) HT120 E L2 69K Thermoelectric Cooler Qmax 56 W"

 

Manufacturer "Kryotherm"
Related links of the manufacturer

Customers also bought

2,5A Chassis Mount Temp Controller PTC2.5K-CH
The PTC-CH Series Chassis Mount Temperature Controllers deliver the precision performance and long-term reliability you expect from a Wavelength Electronics temperature controller. PTC-CH Series controllers are found in such diverse applications as particle and droplet measurement, manufacturing machine vision systems, biomolecular interaction analysis, and more.The PTC-CH controllers operate from a single power supply between 4.5 V and 30 V, and a selection of models allows you to optimize the current output level for your application. The linear bipolar controller drives a Peltier thermoelectric cooler or a resistive heater, and the chassis-mount package integrates easily into OEM applications. PTC-CH controllers interface with a variety of temperature sensors, and the bias current is adjustable in order to maximize controller sensitivity and stability for your application.The compact chassis-mount design simplifies heatsinking and requires minimal space. PTC-CH controllers are quick to configure for your prototype project, and there are no surprises when it's time to integrate the controller into the final design.Practical Features For Real-World Conditions Built-in features make your product more robust to real-world operating conditions and minimize your electronics overhead: If the optional remote temperature setpoint signal is lost, the controller defaults to a standard "safe" temperature setpoint (25ºC when a 10 k© thermistor is used). The safe temperature can be changed at the factory; call for details. An on-board trimpot is used to set the output current limit to prevent over-driving the TEC, and helps protect your load from thermal runaway situations. Proportional gain is easily adjusted with an on-board trimpot. Low temperature coefficient design remains stable across a wide range of ambient conditions. When used with Wavelength's laser drivers, such as the PLD Series, these temperature controllers provide stable and reliable performance that sets your system apart from your competitors' and keeps your customers satisfied. Key Features Drive up to ±2.5, ±5.0, or ±10.0 A of linear bipolar TEC or heater current Add a booster unit to drive up to ±20.0 A Single supply operation: 5 to 30 VDC Small package: 3.0" x 3.2" x 1.1" Use a wide variety of temperature sensors Remote Output and Setpoint controls Short term stability: 0.0012°C Selectable sensor bias current Adjustable current limit Failsafe Setpoint default in case of remote temperature setpoint signal error
Product number: C008985-6
Manufacturer:

€503.45*
TCS610 NTC Thermistor (1 pack = 10 pieces)
10 kΩ; ±1%; Bead Head; 3.04x2.4 mm; Phenolic Resin The TCS610 by Wavelength Electronics is an NTC bead head thermistor sold in packs of 10 that can be used with following temperature controllers and laser diode drivers from Wavelength Electronics: HTC1500, HTC1500-62, HTC3000, HTC3000-62, HTC4000-62, MPT2500, MPT5000, MPT10000, PID1500, PTC5000, PTC10000, PTC2.5K-CH, PTC5K-CH, PTC10K-CH, RHM5K-CH, WHY5640, WTC3243, WTC3243HB, WTCP5A5V, LDTC 2/2 O, LDTC 2/2 E, LDTC0520 or LDTC1020. It is conformally coated, two-lead thermistors for applications where embedding the thermistor is required. The coating is baked on phenolic for durability and long term stability. It has solid nickel wires with Teflon® insulation to provide isolation when assembled in metal housings. It is ideal for controlling optical surfaces, thin surfaces and small laser packages. A complete resistance vs. temperature chart is included in the datasheet. Key Features Thermal Resistance or Dissipation Constant is 2-3 mW / °C Thermal Time Constant is 6-14 seconds Low Cost Small Size -- Conformally Coated Wide Resistance Range Available in 5 Different R-T Curves 1% Tolerance 3" Long Solid Nickel Wire Leads Teflon® Insulation Provides Isolation from Metal Housing RoHS Compliant (by exemption)  
Product number: C008950-6
Manufacturer:

Content: 10 pcs (€15.72* / 1 pcs)

€157.17*
pac

Customers also viewed

B-Series CMOS Cameras
0.36-5 MP; Pixel Size 2.2x2.2-6.0x6.0 µm; Sensor Size 1/3”-1/2” Diagonal; Colour or B/W; 3-310 fps; Resolution 8-12 bit; USB 2.0; Buffered; Progressive Scan; Dynamic Range >55-70 dB; Board-level or Enclosed Mightex’s B-Series USB 2.0 CMOS cameras with frame buffers are optimized for machine-vision applications, and they can also be used for a wide variety of other applications such as digital microscopy and medical imaging, where quality, ease of use, and cost-effectiveness are crucial. B-Series cameras are available as colour or B/W versions, with resolutions from Wide VGA (WVGA, 752x480) up to 5 MP (2592x1944) and 8, 10 or 12 bit, and they can be ordered as “naked” board-level device or pre-mounted in an enclosure. Monochrome cameras often exhibit a 20% higher spatial resolution than their colour counterparts because no pixel interpolation is necessary. Without a Bayer colour filter on the sensor, monochrome cameras are also more sensitive than colour sensors, especially in near IR and UV regions. Mightex’s B-Series cameras feature built-in frame buffers, global shutter (Wide VGA versions), external trigger-in, strobe-out, and a powerful camera engine that supports multiple cameras. The frame rate can be as high as 60 fps in full resolution and up to 600 fps using ROI mode (depending on colour or B/W and sensor resolution). In addition, a user-friendly GUI based application software and an SDK are provided for custom software development. A DirectShow driver and a TWAIN driver are included (except for 5 MP B/W versions), and a USB command set protocol is provided for non-Windows based applications. A Linux driver is also either included (5 MP and Wide VGA B/W versions) or available upon request. Available models are: BCN-C050-U/BCN-C050-US: 5 MP, colour, lens mount C/CS, board-level BCE-C050-U/BCE-C050-US: 5 MP, colour, lens mount C/CS, enclosed BCN-B050-U/BTN-B050-U: 5 MP, B/W, 8/12 bit, lens mount C or CS, board-level BCE-B050-U/BTE-B050-U: 5 MP, B/W, 8/12 bit, lens mount C or CS, enclosed BCN-C030-U/BCN-C030-US: 3 MP, colour, lens mount C/CS, board-level BCE-C030-U/BCE-C030-US: 3 MP, colour, lens mount C/CS, enclosed BCN-B013-U/BCN-B013-US: 1.3 MP, B/W, 8 bit, lens mount C/CS, board-level BCE-B013-U/BCE-B013-US: 1.3 MP, B/W, 8 bit, lens mount C/CS, enclosed BTN-B013-U/BTN-B013-US: 1.3 MP, B/W, 10 bit, lens mount C/CS, board-level BTE-B013-U/BTE-B013-US: 1.3 MP, B/W, 10 bit, lens mount C/CS, enclosed BCN-CG04-U/BCN-CG04-US: WVGA, colour, lens mount C/CS, board-level BCE-CG04-U/BCE-CG04-US: WVGA, colour, lens mount C/CS, enclosed BCN-BG04-U/BCN-BG04-US: WVGA, B/W, 8 bit, lens mount C/CS, board-level BCE-BG04-U/BCE-BG04-US: WVGA, B/W, 8 bit, lens mount C/CS, enclosed BTN-BG04-U/BTN-BG04-US: WVGA, B/W, 10 bit, lens mount C/CS, board-level BTE-BG04-U/BTE-BG04-US: WVGA, B/W, 10 bit, lens mount C/CS, enclosed Note: Board-level cameras are designed for OEM applications, when a system-level enclosure is usually provided. In order to avoid electro-static discharge (ESD) related damages, workforce handling a board-level camera should be properly grounded. ESD related damages are considered as mishandling and are not covered by product warranty. For lab use, it is strongly recommended to choose an enclosed camera instead of a board-level one. Key Features: Colour or Black&White (B/W, Monochrome) Board-level or Enclosed Versions Available Ultra-compact Active Imaging Pixels: 0.36 to 5 MP, 752x480 to 2592x1944 Pixel Size: 2.2 x 2.2 to 6.0 x 6.0 µm Sensor Size (Diagonal): 1/3” to 1/2” Dynamic Range: >55 to 70 dB Buffered, 32 MByte On-board Memory (3 to 23 Frames at Full Resolution, Depending on Sensor) 8, 10 or 12 bit Gray Level Progressive Scanning System Frame Rate: 3 to 310 fps True Global Shutter (Wide VGA Versions) Supports Simultaneous Image Capturing From Multiple Cameras 4-pin GPIOs Arbitrary ROI Supported (Wide VGA Versions) Interface: High-speed USB 2.0 (480 Mbit/s), No Need for External Power Supply Digital Output, No Need for Frame Grabber Custom Programmable With SDK Provided DirectShow & TWAIN Drivers Linux Driver (5 MP and Wide VGA B/W Versions) USB Command Set Protocol for Non-Windows-based Applications External and Software Trigger Strobe Output for External Flash Precise Frame Rate Setting (Wide VGA Versions) ROI (Not Wide VGA Versions) and Pixel Skipping/Binning OEM Versions Available Applications: Machine Vision and Stereo Vision; Medical Imaging; Semiconductor Equipment; Test Instruments; High-quality ID Photo Capture; Document Scanners; Digital Microscopy; Web Camera and Security Video
Product number: SW11205
Manufacturer:
3D SCOPE-V2 Interferometers for Single-Fiber Connectors
Designed for Production Environment; Manual or Autofocus; Field of View 0.7 x 0.5 mm; Measurement Speed 0.5 s; Output USB 2.0; Connector Type LC, SC, SMA Data-Pixel’s 3D SCOPE-V2 series of interferometers for single-fiber connectors have been specifically designed for use in a production environment. These interferometers are robust, compact and easy to use tools that bring speed and precision to operators. 3D SCOPE-V2 interferometers are available in two versions with manual focus or autofocus. The 3D Scope-V2 interferometers support Data-Pixel’s BLINK software platform (included). Non-compressed, real-time and high-quality images are transferred from the hardware to the software via a USB 2.0 link in addition to the automation and control commands. 3D SCOPE-V2 interferometers are compatible with Data-Pixel’s SUPERVISOR software, a MES style software which is in charge of the execution, management and monitoring of the production in an assembly workshop for fiber optic connectors. Its role is to supervise machines and help operators with complete traceability of the manufacturing information. The 3D SCOPE-V2 interferometers are fully compliant with industry standards. Key Features: Measurement of PC and APC Connectors, Ferrules and Bare Fibers Lightning Speed Measurement Cycle (0.5 s) PASS/FAIL Result Visual Feedback Via Front Panel Start-button LED Color Integrated PC/APC Tilt Stage, no APEX Re-calibration Required True Phase-shifting Interferometers Vibration Insensitive Autofocus Option Compliance with Industry Standards for Interferometer Measurements Intuitive BLINK Software With Data-base Connectivity Measurement Report in HTML Format Compatible With Desktop PC, Laptop, Tablet PC Applications: Measuring End-face Geometry of Single-Fiber Connectors
Product number: SW10887
Manufacturer:
CP10G01 Aluminum Cold Plate with 2-Pass Copper tube, straight fittings
152.4 mm X 88.9 mm, 0.059 °C/W, tubed cold plate.The CP10™ 2-pass is a cost-effective, single-sided aluminum cold plate available with either copper or stainless steel tubes. It is ideal for component cooling applications where the heat load is low-to-moderate. Our range of standard tubed cold plates provide cost-effective thermal solutions for component cooling applications where the heat load is low-to-moderate. These tubed cold plates consist of copper or stainless steel tubes pressed into a channeled aluminum extrusion. This “Press-Lock” technology eliminates the need for performance-limiting epoxy between the tube and the plate, resulting in superior thermal performance. Each tubed cold plate has a single tube with no joint, ensuring leak-free operation.
Product number: C008680-6
Manufacturer:
FO(P)I-00 High Power Free Space Isolators
Polarization Sensitive & Insensitive Versions; 1040 nm to 1090 nm; Isolation ≥35 dB; Power Handling ≤80 W; 48 mm x 48 mm x 133 mm The FO(P)I-00 series of free space isolators are featuring options to allow the customer to mount their own fiber pigtailed collimator or beam expander. The OZ Optics tilt adjustment technique gives customers the ability to perform the optical alignment themselves.Isolators are optical devices that allow light to be transmitted in one direction only. They block the source from reflected light, thus preventing any feedback problems, such as frequency instability, relaxation oscillations, amplified stimulated emissions, or optical damage – very critical with the recent dramatic increase in laser output powers, especially in the 1030 to 1090nm wavelength range. To meet this demand OZ Optics has developed a line of high power handling isolators, capable of peak isolation levels of 30 dB to 50 dB for 1030 nm to 1090 nm, depending on the input beam size (with typical beam diameters of 0.4mm to 1.1mm). The isolators come with built-in windows to prevent dust contamination of internal isolator optics. These protection windows are easily removed and replaced by the user. Custom smaller packages can be made for OEM applications – contact us for more details. Key Features: Operating Wavelength Range: 60 nm Power Handling: Up to 80 W Isolation: Up to 50 dB Low Insertion & Polarization-dependent Losses Excellent Beam Quality Removable Protective Windows RoHS compliant Applications: Protection of high power lasers from reflections during a) laser marking and engraving; b) laser cutting and etching of metal surfaces with high reflectance such as Al, Cu, Au or Ag; c) micro machining and trimming  
Product number: SW10365
Manufacturer:
CP20G03 Aluminum Cold Plate with Z shaped Aluminum tube, straight fittings
51 mm x 51 mm, 0.044 °C/W, Flat Tube Cold Plate.The CP20™ aluminum flat tube cold plate is a very thin, compact and lightweight cold plate, consisting of header tubes welded to a unique micro-channel aluminum extrusion. This cold plate offers extremely low thermal resistance, achieved by thin mounting surfaces and internal fin, which create a large surface. It provides excellent thermal uniformity as coolant flows below the entire surface. Its high performance and small size makes it ideal for cooling small, high watt-density components such as thermoelectric modules. The CP20™ is only 3.3 mm (0.13”) thick and 0.05 kg (0.1 lbs), making it ideal for applications where space is limited. Its large internal surface area combined with its low pressure drop makes the CP20™ ideal for use with viscous and poor heat transfer fluids such as EGW, oils, Fluorinert® and Polyalphaolefin (PAO).
Product number: C019211-6
Manufacturer: