46P-30-5D Polishing Film

146x146x3mm; 70 durometer         The process of polishing fiber optic connector endfaces requires both a hard, flat surface and a cushioned pad. Our fiber optic polish pads provide the necessary foundation for your polish film, enabling you to achieve the quality endface finish required of fiber optic connectors. Placing your fiber optic polishing film over the right type of pad ensures the removal of epoxy and enables you to polish your fiber optic connector without destroying the pre-radius of the ferrule.  

5 inch Disc; Grit 9 µm; Diamond; Ceramic Ferrule; no PSA The 66HPX-9-5D fiber optics polishing film from Nanolap comes in a pack that contains 5 pieces.

ST/SC/FC; stainless steel When hand polishing fiber optic connectors, you can't afford to leave anything to chance.  These Fiber Optic Hand Polishing Discs, or hockey pucks as some installers call them, enable you to achieve quality endface finishes and consistent results time after time.  

Refractive Index 1.56; 250 cps Viscosity at 25°C Norland Optical Adhesive 88 ("NOA 88") is an optically clear, liquid adhesive that will cure when exposed to long wavelength ultraviolet light. The adhesive is a one-part, 100% solids material that offers advantages in optical bonding applications. The use of NOA 88 eliminates premixing, drying, or heat curing operations common to other adhesive systems. Curing time can be regulated by the end user by varying the intensity of the curing source.NOA 88 was formulated as a low outgassing (CVCM) and low Total Mass Loss (TML) adhesive. The ideal applications for this adhesive is for coating of parts destined for space exploration, bonding of high tech computer components,adhering parts in very sensitive instruments and coating sensitive components.NOA 88 is cured by ultraviolet light (315 nm to 395nm) with maximum sensitivity at 365 nanometers. The adhesive requires 5 Joules/sq.cm of energy to fully cure a 25 to 50 micron bond. The material has low oxygen inhibition, so adhesive exposed to air will cure tack-free with sufficient exposure to UV light.Typical Properties of NOA 88 Solids 100% Refractive Index of Monomer 1.52 Elongation at Failure 41% Modulus of Elasticity (psi) 131,000 Tensile Strength (psi) 2,000 Hardness - Shore D 90 Total Mass Loss (TML) 1.07% Collected Volatile Condensable Material (CVCM) <0.01% Dielectric Constant (1 MHz) 4.06 Dielectric Strength (V/mil) 457 Dissipation Factor (1 MHz) 0.0341 Volume Resistivity (ohm-cm) 6.85 x 10 to the 14 power Surface Resistivity (MEgohms) 3.71 x 10 to the 12 power The shelf life of the liquid material is at least four months from the shipment date if kept in a cool (5-22° C) dark place in the original container. If refrigerated, allow the adhesive to come to room temperature prior to use.

228x330x12.7 mm; Safety glass; 6.35 mm glass thickness; 1.06 kg    Our fiber optic polish plates provide the necessary foundation for your polish film, enabling you to achieve the quality endface finish required of fiber optic connectors.  

Refractive Index 1.54; 5,000 cps Viscosity at 25°C Norland Optical Adhesive 68 ("NOA68")is a clear, colorless, liquid photopolymer that will cure when exposed to ultraviolet light. Since it is a one part system and 100% solids, it offers many advantages in bonding of optical materials where the bonding surface can be exposed to light. The use of NOA 68 eliminates premixing, drying and heat curing operations common to other optical adhesive systems. Curing time is remarkably fast, and is dependent upon the thickness applied and the amount of ultraviolet light energy available.NOA 68 is designed to give improved adhesion to many plastics such as acrylic, polycarbonate and cellulose acetate butyrate. In addition to plastics, NOA 68 has good adhesion to glass and metals and can be used to bond combinations of the three. Suggested uses for NOA 68 include bonding compound plastic lenses, laminating polarized film between glass or plastic, mounting plastic lenses in metal or plastic mounts and bonding cover glasses.Typical Properties of NOA 65 Solids 100% Elongation at Failure 80% Modulus of Elasticity (psi) 20,000 Tensile Strength (psi) 2,500 Hardness - Shore D 60 Shelf life of the liquid is at least 6 months from the date of shipment if stored in a cool (5-22° C), dark place in the original container. If refrigerated, allow the adhesive to come to room temperature prior to use.