mRC-C-450-100/240 mini Recirculating Chiller

Compact Vapor Compression Chillers; Cooling Capacity 450-1000 W @+25°C; Single and Twin Versions; 1 to 5.5 l/min; Temperature Stability ≥±0.05K; Interface USB/Serial, Ethernet AMS Technologies’ mRC-KITs are “mini Recirculating Chiller” development kits for creating particularly compact compressor-based water cooling systems. All mRC-KIT versions feature vapor compression circuits and closed, pressurized recirculating water circuits. On the refrigeration side, miniature rotary compressors as well as customized condensers and evaporators are utilized to reduce the size. The compressor’s BLDC motor is speed controlled by an inverter, eliminating annoying switching noise of hot gas bypass known from ON/OFF compressors. Throughout its speed range, the compressor twin pump design offers low vibration and low noise. Compact centrifugal pumps on the water circuit side also contribute to the compact size Since the water circuit is pressurized, the mRC-KITs manage with very small tanks – without the risk of cavitation in the smoothly operating centrifugal pumps. Overpressure on the cooling system also prevents the ingress of bacteria and oxygen and thus extends the maintenance intervals. While mRC-C-450-24-KIT and mRC-C-450-100/240 feature full chiller power and up to 450 W cooling capacity in a shoe box form factor, DmRC-C-900-100/240-KIT provides two independent water cooling systems in a 19-inch rackmount insert, which can provide a combined maximum cooling capacity of 900 W – either with each circuit cooling two heat loads independently of each other or with both circuits coupled in series, if only one circuit is needed. Our mRC-KITs are available either with a 24 VDC or with a 90 to 264 VAC wide-input-range power supply. The mRC-C-1000-100/240 can also be shipped as a 24V option to target OEM integration applications, that need a cooling capacity of around 1000W and where noise and vibrations are an issue. Automatic fill and drain: Using automatic air and water pump technology integrated into the unit, the cooling water in the tank and pipe system of the mRC-KITs can be easily filled and drained at the push of a button – without the need for time-consuming tilting or removing the unit or the tank from the system and avoiding annoying spills or leaks. mRC Recirculating ChillersIn addition to our mRC-KITs, AMS Technologies provides two recirculating chillers that are CE certified and available from stock. mRC-C-450-100/240 provides up to 500 W cooling capacity, while mRC-C-1000-100/240 features a more powerful compressor, capable of cooling capacities up to 1000 W. Both systems come with an integrated 90 to 264 VAC wide-input-range power supply.  IoT ready: An integrated Ethernet interface allows access to system parameters of the mRC recirculating chillers as well as remote control of the cooling systems via a web browser. Your customized mRC-KIT: For customer requirements that cannot be covered by mRC-C-450-24-KIT, mRC-C-450-100/240 or DmRC-C-900-100/240-KIT, our thermal management specialists at AMS Technologies are happy to develop a completely tailor-made solution and offer all services from development and proof-of-concept all the way to series production. Contact us now to discuss your customized mRC-KIT! Key Features: Recirculating Water Chilling Kits Ideal for Water Cooling Tasks up to 1000 W Cooling Capacity (Twater +25°C, Tambient +35°C) High Cooling Capacity in Compact Format, Easy to be Integrated in Customer Application 24 VDC and 100 to 240 VAC Derivatives Available Temperature Stability: Down to ±0.05 K Flow Rate: 0.5 bar @ 5.5 lpm (standard), 5 bar @ 5 lpm (optional) Smooth, Low-noise Operation with Low Vibration Automatic Fill & Drain PID Parameters and Fan Speed Adjustable Interfaces: USB/Serial, Ethernet (IoT Enabled) Applications: Water Cooling of Lasers and Other Applications; Integration of Water Cooling Capabilities up to 1000 W in Systems with Limited Space

Siskiyou’s OT series of optic translators use color coded Soft Touch knob caps in both non-lockable and lockable versions. These knob caps are comfortable to use and provide quick axis location in low light conditions.80-pitch screws are the basis for smooth accurate positioning of all models from the smallest mount to the largest. To meet the demands of many different applications we have XY, XYZ and 5-axis OT series optic translators in three sizes. Te entire OT series comes standard with Delrin® retaining rings and a separate optic adapter. The new OTX series is an even more robust OEM version of the OT translators. The OTX series has been designed to absorb a 4G jolt without moving more than 5 microns. Locks on all axes make them perfect for applications where any misalignment during shipping cannot be tolerated. 

0.36-5 MP; Pixel Size 2.2x2.2-6.0x6.0 µm; Sensor Size 1/3”-1/2” Diagonal; Colour or B/W; 3-310 fps; Resolution 8-12 bit; USB 2.0; Buffered; Progressive Scan; Dynamic Range >55-70 dB; Board-level or Enclosed Mightex’s B-Series USB 2.0 CMOS cameras with frame buffers are optimized for machine-vision applications, and they can also be used for a wide variety of other applications such as digital microscopy and medical imaging, where quality, ease of use, and cost-effectiveness are crucial. B-Series cameras are available as colour or B/W versions, with resolutions from Wide VGA (WVGA, 752x480) up to 5 MP (2592x1944) and 8, 10 or 12 bit, and they can be ordered as “naked” board-level device or pre-mounted in an enclosure. Monochrome cameras often exhibit a 20% higher spatial resolution than their colour counterparts because no pixel interpolation is necessary. Without a Bayer colour filter on the sensor, monochrome cameras are also more sensitive than colour sensors, especially in near IR and UV regions. Mightex’s B-Series cameras feature built-in frame buffers, global shutter (Wide VGA versions), external trigger-in, strobe-out, and a powerful camera engine that supports multiple cameras. The frame rate can be as high as 60 fps in full resolution and up to 600 fps using ROI mode (depending on colour or B/W and sensor resolution). In addition, a user-friendly GUI based application software and an SDK are provided for custom software development. A DirectShow driver and a TWAIN driver are included (except for 5 MP B/W versions), and a USB command set protocol is provided for non-Windows based applications. A Linux driver is also either included (5 MP and Wide VGA B/W versions) or available upon request. Available models are: BCN-C050-U/BCN-C050-US: 5 MP, colour, lens mount C/CS, board-level BCE-C050-U/BCE-C050-US: 5 MP, colour, lens mount C/CS, enclosed BCN-B050-U/BTN-B050-U: 5 MP, B/W, 8/12 bit, lens mount C or CS, board-level BCE-B050-U/BTE-B050-U: 5 MP, B/W, 8/12 bit, lens mount C or CS, enclosed BCN-C030-U/BCN-C030-US: 3 MP, colour, lens mount C/CS, board-level BCE-C030-U/BCE-C030-US: 3 MP, colour, lens mount C/CS, enclosed BCN-B013-U/BCN-B013-US: 1.3 MP, B/W, 8 bit, lens mount C/CS, board-level BCE-B013-U/BCE-B013-US: 1.3 MP, B/W, 8 bit, lens mount C/CS, enclosed BTN-B013-U/BTN-B013-US: 1.3 MP, B/W, 10 bit, lens mount C/CS, board-level BTE-B013-U/BTE-B013-US: 1.3 MP, B/W, 10 bit, lens mount C/CS, enclosed BCN-CG04-U/BCN-CG04-US: WVGA, colour, lens mount C/CS, board-level BCE-CG04-U/BCE-CG04-US: WVGA, colour, lens mount C/CS, enclosed BCN-BG04-U/BCN-BG04-US: WVGA, B/W, 8 bit, lens mount C/CS, board-level BCE-BG04-U/BCE-BG04-US: WVGA, B/W, 8 bit, lens mount C/CS, enclosed BTN-BG04-U/BTN-BG04-US: WVGA, B/W, 10 bit, lens mount C/CS, board-level BTE-BG04-U/BTE-BG04-US: WVGA, B/W, 10 bit, lens mount C/CS, enclosed Note: Board-level cameras are designed for OEM applications, when a system-level enclosure is usually provided. In order to avoid electro-static discharge (ESD) related damages, workforce handling a board-level camera should be properly grounded. ESD related damages are considered as mishandling and are not covered by product warranty. For lab use, it is strongly recommended to choose an enclosed camera instead of a board-level one. Key Features: Colour or Black&White (B/W, Monochrome) Board-level or Enclosed Versions Available Ultra-compact Active Imaging Pixels: 0.36 to 5 MP, 752x480 to 2592x1944 Pixel Size: 2.2 x 2.2 to 6.0 x 6.0 µm Sensor Size (Diagonal): 1/3” to 1/2” Dynamic Range: >55 to 70 dB Buffered, 32 MByte On-board Memory (3 to 23 Frames at Full Resolution, Depending on Sensor) 8, 10 or 12 bit Gray Level Progressive Scanning System Frame Rate: 3 to 310 fps True Global Shutter (Wide VGA Versions) Supports Simultaneous Image Capturing From Multiple Cameras 4-pin GPIOs Arbitrary ROI Supported (Wide VGA Versions) Interface: High-speed USB 2.0 (480 Mbit/s), No Need for External Power Supply Digital Output, No Need for Frame Grabber Custom Programmable With SDK Provided DirectShow & TWAIN Drivers Linux Driver (5 MP and Wide VGA B/W Versions) USB Command Set Protocol for Non-Windows-based Applications External and Software Trigger Strobe Output for External Flash Precise Frame Rate Setting (Wide VGA Versions) ROI (Not Wide VGA Versions) and Pixel Skipping/Binning OEM Versions Available Applications: Machine Vision and Stereo Vision; Medical Imaging; Semiconductor Equipment; Test Instruments; High-quality ID Photo Capture; Document Scanners; Digital Microscopy; Web Camera and Security Video

Cabinet Cooler - 46W Cooling Capacity - TEC based – 60-12-AA