Accessories for LED Light Sources

Output Current TEC ±10, ±15 A; Benchtop or Rack Mount; Supply Voltage 100-240 VAC; USB, Ethernet Communication Interface; Temperature Stability 0.0009°CWavelength Electronics’ TC LAB series of instrument type temperature controllers integrates high-end digital control with a precision output current drive stage to offer the best stability temperature control instrument commercially available today. Many different sensors can be used in the feedback loop including thermistors, RTDs, linear current and voltage sensors. Within the TC LAB series, two models are available driving a thermoelectric or resistive heater with maximum currents of 10 A (TC10 LAB) with 15 V compliance or 15 A maximum (TC5 LAB) with 20 V compliance. The advanced and reliable circuitry of the TC LAB series instruments achieves better than 0.0009 °C temperature stability with thermistors. Safety features protect the thermoelectric cooler [TEC] and its load. Over and under temperature limits as well as positive and negative current limits can be set. If the sensor signal is lost or a short is detected at the TEC, output current is disabled. If temperature limits are exceeded, a signal to the active load can be sent to disable its current. For example, connect the LD Shutdown BNC output to the Active Lock input on Wavelength Electronics’ QCL LAB driver, and the QCL current will shut down if temperature limits are exceeded. An auxiliary sensor can be used to monitor the temperature of the system heatsink. With Wavelength’s plug and play instrument, you have the ability to quickly set the controls using either the instrument touch screen or a remote computer, and results are easy to monitor. This allows taking your temperature-controlled application from the test bench to market quickly and efficiently. Wavelength Electronics’ proprietary IntelliTune® algorithm characterizes the TEC/sensor system’s response to the controller and determines the optimal PID control coefficients. It then automatically adjusts the PID control values as setpoint, tuning mode, or bias current change. Run IntelliTune® easily just off ambient and watch it change PID settings for a much higher or lower setpoint. After a single scan, explore either optimized setpoint response or disturbance rejection performance with your load to see which works best. Add or remove the D term to see if noise is an issue. IntelliTune® lets you skip the manual characterization and it’s smart enough to really work—very little adjustment is needed after you have stored a successful characterization scan. See Application Note IntelliTune® vs. Conventional Autotune for an in-depth exploration. One mating DB 15+2 thermoelectric and sensor plug is included with the instrument. As accessories, various further devices are available, like a DB9 mating connector for status/enable signals, a DB15+2 male connector with hood and high current pin inserts, full cables for the DB9 and DB15+2 or single and dual rack mount kits. When controlling laser diode temperature, the LDMOUNT-5A, a 14-pin butterfly laser diode mount with integrated heat sinking, is available for simple connections between the instrument and the laser. If you need a lower power temperature control instrument, consider the LFI3751 series. Free, effective and responsive technical support is available to simplify integration of Wavelength products into your OEM design. Standard products can be easily modified to meet your application requirements. Get in touch with the AMS Technologies laser diode driver experts to discuss your customized solution! Key Features: Instrument Type, Benchtop Use Size: 89 x 221 x 450 mm 19" Rack Mountable, 2 U Half Rack Output Current up to ±15 A Supply Range: 100 to 240 VAC (±10%), 3A, 50 to 60 Hz Compliance Voltage 20 V Compatible With Most Sensor Types (Thermistor, RTD, IC, IR) Temperature Stability Better than 0.0009 °C Intuitive User Interface Touchscreen IntelliTune® PID Control, Setpoint Response or Disturbance Rejection Optimization Adjustable Current Limits Over- and Under-temperature Protection USB, Ethernet Interfaces Applications: Research in Electro-optical, Medical, Spectroscopy and Defense Systems; Communications; Manufacturing; Particle and Droplet Measurement; Manufacturing Test; Airborne Instrumentation; Spectroscopic Monitors; Medical Diagnostic Equipment

653-1120 nm; Spectral Width 2-10 nm; Output Power 1-19 W (CW), 1.8-90 W (Pulsed); Threshold Current ≤500-3000 mA; Slope Efficiency 0.6-1.0 W/A; Forward Current 1,6-100 AToptica egleyard’s BAL series of multi mode laser diodes are high brightness, broad area laser (BAL) diodes operating multi mode spatially and longitudinally. Within the BAL series, wavelengths between 653 and 1,120 nm are available with output powers between 1 and 19 W in cw mode or even up to 90 W in pulse mode.Its high pulse energy and fast rise time makes the BAL series of multi mode laser diodes the laser source of choice for high resolution sensing applications under harsh environmental conditions. Stripe widths from 100 to 400 µm are available to optimize beam structure and power for the application.Toptica eagleyard’s hermetically sealed TO packages as well as C-mount or fiber pigtailed flat packages make such laser diodes ideally suited for applications with either demanding size restrictions or with preferred fiber pigtail handling. The output power of the fiber of a cost efficient pigtailed single emitter starts at 1 W and reaches up to 90 W peak in pulsed mode.Key Features:Broad Area, Edge Emitting Laser DiodesBroad Wavelength Range: 653 to 1,120 nmHigh Output Power: 1 to 19 W (CW) and 1.8 to 90 W (Pulsed)Hermetically SealedFast/Slow Axis CollimationTyp. Spectral Width: 2 to 10 nmStripe Width: 100 to 400 µmCavity Length: 1 to 4 mmBeam Divergence: Parallel (Slow Axis) 1.5° to 10° (FWHM), Perpendicular (Fast Axis) 0.6° to 30° (FWHM)Extreme Operating Temperature Range: -60 to +90 °CPackages: C-Mount, 9 mm TO TO with Thread, Integrated FAC/SAC, Flatpack With Window ProductWavelengthOutput PowerOperational ModePackageSpecificsBAL-0653-01000-1510-CMT02-0000653 nm1 WCWC-Mount 2 mmPowerful, High Brightness, Longitudinally Multi ModeBAL-0670-00001-1510-SOT23-0010670 nm1.5 WPulsedTO-Can 9 mmSuitable for Harsh EnvironmentsBAL-0670-00004-1510-SOT23-0010670 nm4 WPulsedTO-Can 9 mmSuitable for Harsh EnvironmentsBAL-0670-00010-1510-SOT23-0016670 nm10 WPulsedTO-Can 9 mmSuitable for Harsh EnvironmentsBAL-0808-00005-2013-SOT12-0010808 nm6 WPulsedTO-Can 9 mmSuitable for Harsh EnvironmentsBAL-0808-08000-4020-CMT04-0000808 nm8 WCWC-Mount 4 mmSuitable for Harsh EnvironmentsBAL-0808-00020-4020-FLW01-0010808 nm20 WPulsedFlatpack With WindowSuitable for Harsh EnvironmentsBAL-0808-00025-2013-SOT23-0016808 nm25 WPulsedTO-Can 9 mmSuitable for Harsh EnvironmentsBAL-0905-00010-1040-TOE02-0010905 nm12 WPulsedTO With ThreadSuitable for Harsh EnvironmentsBAL-0905-00050-1040-TOE22-0010905 nm50 WPulsedTO With ThreadSuitable for Harsh EnvironmentsBAL-0905-00090-1040-TOE22-0010905 nm90 WPulsedTO With ThreadSuitable for Harsh EnvironmentsBAL-0980-08000-4020-CMT04-0000980 nm8 WCWC-Mount 4 mmSuitable for Harsh EnvironmentsBAL-1064-08000-4020-CMT04-00001064 nm8 WCWC-Mount 4 mmSuitable for Harsh EnvironmentsApplications: Time-of-Flight LIDAR; Laser Sensing in Missiles; Laser Ignitors of Optopyro Elements for Satellites or Launchers; Active Protection Systems; Material Processing; Medical; Solid-state Laser PumpingPlease note that TOPTICA eagleyard products are not availble from us in Denmark, Finland, Iceland, Norway, and Sweden. 

Single Mode Patchcords, Metal Solder; Polarization Extinction Ratio >20, >25, >30 dB; Helium Leak Rate<10-8 ATM-cc/s; Operating Temperature -40 to +85 °C; Max. Installation Temperature +210 °C OZ Optics’ HSMJ series of hermetically sealable single mode patchcords with metal solder are designed for today's stringent requirements for component packaging. Utilizing metalized fiber and a proprietary sealing process, these patchcords feature a rugged hermetic feedthrough that can be soldered into an opto-electronic package using standard tin/lead solders. The hermetic seal tube is gold plated to promote good on-site sealing and corrosion resistance. These assemblies are capable of easily creating a seal that meets industry hermeticity requirements. Key Features: High Polarization Extinction Ratios up to 30 dB Single or Multiple Fiber Designs up to 24 Channels Ribbon Fiber Versions Available Can be Installed into Packages with Standard Solders Gold Plated Seal Tube for Easy Sealability and Corrosion Resistance Terminated with Round or Rectangular Ferrules Designed to Meet Telcordia Rrequirements Custom Configurations Possible Applications: Laser Diode Packaging; Waveguide Packaging; Integrated Optics Packaging; Vacuum Feedthrough Assemblies

The Microtiter Temperature Control Plate from Solid State Cooling Systems delivers uniform, precision thermal regulation for microplates used in automated laboratory workflows. Designed to meet the ANSI/SBS 2004-1 standard, this compact cold plate ensures ±0.1°C temperature stability across the entire surface, making it ideal for high-throughput screening, diagnostics, and life sciences applications where thermal consistency is critical.Unlike traditional heating and cooling methods that can introduce variability or delay, the Microtiter Plate uses a precisely controlled recirculating fluid to maintain target temperatures. This approach not only ensures rapid response to load changes but also removes waste heat from the lab automation stage, preserving the integrity of sensitive assays and reducing thermal interference with surrounding equipment.Key featuresPrecision temperature control: Maintains ±0.1°C stability and repeatability, even under dynamic load conditions.Wide operating range: Supports temperatures from 0°C to 65°C (extendable to -5°C with compatible chillers), accommodating a broad spectrum of experimental needs.Standardized compatibility: Designed for ANSI/SBS 2004-1 standard microplates, ensuring seamless integration with most lab automation platforms.Recirculating fluid system: Utilizes a closed-loop fluid path for consistent thermal performance and efficient heat removal.Rapid thermal response: Adapts quickly to changes in thermal load, minimizing downtime and improving throughput.Flexible integration: Available in two configurations—with short side or long side fluid connections—to suit various deck layouts.Compact and low-profile: With a top surface height of just 1.181”, it fits easily into tight automation spaces.Self-leveling feet and alignment marks: Patented design simplifies robotic alignment and ensures stable, level placement.Durable construction: Made with aluminum and polymer wetted materials for long-term reliability and chemical compatibility.Versatile connectivity: Comes standard with 1/4” NS2 DESO fittings, with other fitting types available upon request.Optimized for SSCS chillers: Pairs seamlessly with UC160-190, TCube Edge, or ThermoCube models using centrifugal pumps.Enhanced thermal insulation: Optional three-layer insulated hoses improve efficiency and minimize heat loss.ApplicationsThe Microtiter Temperature Control Plate is purpose-built for a wide range of laboratory and industrial applications:High-throughput screening (HTS): Ensures consistent assay conditions across all wells in microplates.Life sciences and diagnostics: Maintains precise temperatures for enzyme reactions, PCR, and cell-based assays.Pharmaceutical R&D: Supports drug discovery workflows requiring tight thermal control of reagents and samples.Biotechnology and genomics: Enables accurate temperature regulation for DNA/RNA amplification and sequencing prep.Lab automation systems: Integrates easily into robotic platforms for on-deck temperature control without disrupting workflows.What's next?As laboratories continue to push the boundaries of automation and precision, Solid State Cooling Systems remains committed to delivering innovative thermal solutions. The Microtiter Temperature Control Plate exemplifies this mission—offering unmatched accuracy, flexibility, and integration for modern lab environments.To learn more or request a quote contact AMS Technologies.

Cooling Capacity 160 to 190 W @+20 °C; Process Fluid Flow Rate 0.35 lpm @ 14 psig; 1/8" Female Valved CPC Fittings; Magnetically-coupled Gear Pump; Wetted Materials: Aluminium (or Copper) & PolymersThe UC160-190 Thermoelectric Recirculating Chiller by Solid State Cooling Systems redefines compact precision cooling for laboratory and industrial applications. Designed for environments where space, reliability, and thermal stability are critical, this advanced chiller delivers 160 to 190 watts of cooling capacity in an ultra-compact footprint. With precise temperature control ranging from 2°C to 45°C, it ensures consistent performance for sensitive instruments and OEM systems.Unlike conventional compressor-based chillers, the UC160-190 leverages solid-state thermoelectric technology, eliminating the need for refrigerants. Its small form factor—just 7.5 inches (19.1 cm) x 5 inches (12.7 cm) x 7 inches (17.8 cm)—and lightweight build (under 8 lbs / 3.6 kg) make it ideal for integration into tight spaces without compromising cooling performance. With ±0.1°C temperature stability and rapid response to thermal loads, it supports critical applications with unmatched reliability.Key FeaturesThermoelectric Cooling Technology: Offers long operational life with no moving compressor parts and no refrigerants.Compact and Lightweight: The smallest air-cooled recirculating chiller in its class, perfect for space-constrained setups.Precision Temperature Control: Maintains ±0.1°C stability across a broad operating range (2°C to 45°C).Customizable Pump Options: G1 and G3 magnetically-coupled gear pumps available, delivering flow rates up to 0.7 lpm.Low Power Operation: Consumes less than 200 watts with universal AC input (100–240 VAC) or 13.5 VDC external supply.Integrated Communication: RS232 interface and keypad control for easy system integration and automation.Safety Features: Includes alarms for temperature deviations, fluid level, and system faults; certified to UL, CE, and CAN/CSA standards.ApplicationsThe UC160-190 Thermoelectric Recirculating Chiller is engineered for high-precision cooling in a variety of scientific and industrial contexts:CCD and CMOS Cameras: Maintains optimal sensor temperatures for consistent imaging quality.Analytical Instrumentation: Supports stable operation in spectroscopy, chromatography, and other sensitive systems.Laboratory Automation: Ideal for microtiter plate cooling and point-of-use thermal control in automated workflows.OEM Equipment: Compact design and universal power input make it easy to integrate into medical and scientific devices.Laser and Photonics Systems: Ensures thermal stability for diode lasers and photonic components, enhancing performance and longevity.What's Next?If your application demands compact, reliable, and precise thermal control, the UC160-190 Thermoelectric Recirculating Chiller is the solution. With over 200,000 hours of thermoelectric module life and a design optimized for precision, it delivers consistent performance in the most demanding environments.Contact our experts today to request a quote, discuss your application, or download the product datasheet. Discover how the UC160-190 can enhance your system’s thermal management capabilities.

Fixed; Fiber Type SMF-28; 1425-1605 nm; Fiber Length 0.5, 1 m; Connector Type FC/PC, FC/APC, SC/APC, FC/UPC, SC/UPC, LC, None; Attenuation 1-20 dB, Other; Dimensions Ø3.0x55/65, Ø5.0x80, 80x10x8 mm Gooch & Housego’s AFF-X series of fixed attenuators are compact fused fiber components that reduce optical power by a specified amount. Gooch & Housego (G&H) utilizes a proprietary manufacturing technology that provides accurate attenuation with low wavelength, temperature and polarization dependence. Designed for use where optical power levels need to be managed, G&H’s AFF-xxx0 xBxxx components have standard attenuation values ranging from 1 to 20 dB. Standard wavelength windows are the C, L, C+L or S bands. Attenuators may also be optimized for custom attenuation levels, tolerances and wavelengths – contact AMS Technologies to discuss your customized attenuator solution. Key Features: Fixed Attenuation: 1 to 20 dB, Other Values on Request High Performance Low Back Reflection – Return Loss (RL): 55 dB Proven Reliability C, L, C+L or S Band, 1425 to 1605 nm Wavelength Dependent Loss (WDL): ≤0.10 to ≤1.20 dB Polarization Dependent Loss (PDL): ≤0.09 to ≤0.80 dB Fiber Type: Corning SMF-28 Pigtail Length: 0.5, 1 m Connector Type: FC/PC, FC/APC, SC/APC, FC/UPC, SC/UPC, LC, None Custom Parts Available Compliance: Telcordia GR-1221 Dimensions: Ø3.0 x 55/65, Ø5.0 x 80, 80 x 10 x 8 mm Applications: Power Management in Optical Networks; Receiver Protection; WDM System Channel Balancing; Test Equipment; Fiber Lasers; Sensors