TF-100 Digital Tunable Filters

Ideal for OEM Applications; 1470 to 1620 nm; Line Width 1.1 nm, 0.3 nm Optional; Insertion Loss <2.0 dB; PDL <0.3 dB; Fiber Type SM, MM, PM; Connector Type FC/PC, ST, SC, LC, MU, None OZ Optics’ TF-100-11 series of motor driven tunable filters consist of a collimating optical assembly, an adjustable narrow bandpass filter and a focusing optical assembly to collect the light again. This series consist of pigtailed units with a computer interface which has options for different communication standards. The devices allow to control the wavelength at which the filter transmits work by adjusting the angle of incidence between the filter and the incident beam. The TF-100-11 series motor driven tunable filters are calibrated such that the user directly enters the wavelength to transmit via the computer interface. An RS232 interface with cable is standard. Filter linewidths are normally defined in terms of full width at half maximum (FWHM). The standard filters used have a smooth, rounded transmission spectrum that is the result of a single Fabry Perot type cavity, simply made up of two reflectors separated by a fixed spacer of some thickness. Other filter profiles are available. For instance, flat top bandpass filters are made by stacking multiple cavities together. By increasing the number of cavities one can increase the roll-off slope therefore improving the out-of-band rejection level. Please contact AMS Technologies for custom filter designs that meet your requirements. OZ Optics tunable filters utilize an optical technique to control polarization dependent loss (PDL). This new design reduces PDL to below 0.3 dB, while at the same time making the spectral response polarization insensitive. This feature makes the TF-100-11 series ideal for today's DWDM system applications. Tunable filters using single mode (SM), multi mode (MM) or polarization maintaining (PM) fibers are offered. In general, OZ Optics uses polarization maintaining fibers based on the PANDA fiber structure when building polarization maintaining components and patch cords. However, OZ Optics can construct devices using other PM fiber structures. OZ Optics also carries some alternative fiber types in stock, please contact AMS Technologies for availability. If necessary, OZ Optics is willing to use customer supplied fibers to build devices. In addition to the TF-100-11 series of motor driven tunable filters, OZ Optics provides four further series of tunable filters – TF-100 series of digital tunable filters, TF-11 series of manually adjustable polarization insensitive tunable filters, BTF-11 series of manually adjustable variable bandwidth tunable filters and finally BTF-100 series of motorized adjustable variable bandwidth tunable filters. If you are looking for filters with a fixed wavelength, have a look at OZ Optics’ FF series of fixed filters. Key Features: Narrow Linewidth Polarization Insensitive Wide Wavelength Range Single Mode (SM), Multi Mode (MM) and Polarization Maintaining (PM) Fiber Versions High Resolution Built in Computer RS232 Interface GPIB/RS232 Converter Applications: Dense Wavelength Division Multiplexing; Tunable Sources; Spectral Analysis; Quality Control and Measurement; Product Development; Fiber Optic Component Manufacturing; Automated Testing

Single Mode Patchcords; 200 to 2000 nm; Fiber Type SM High Power; Optional Cooling Fins OZ Optics’ QSMJ series of single mode fiber optic patchcords is specifically designed for high-power applications. These patchcords feature special high-power SM fibers, carefully prepared fiber endfaces and specially designed fiber optic connectors to ensure maximum power handling for your application. In standard connectors the fibers are glued into place, and the fiber is polished flush with the connector ferrule tip. When used with high power lasers, heat generated at the tip of the fiber causes the surrounding epoxy to break down and give off gases. These gases, in turn, burn onto the tip of the fiber, causing catastrophic damage to the fiber and perhaps the entire system. In contrast, OZ Optics’ high-power connectors feature an air-gap design, where the fiber extends into free space by 1.1 to 1.5 mm, providing an epoxy-free region where thermal energy is safely dissipated without burning the surrounding material. OZ Optics offers an adjustable focus feature in both SMA and FC connector designs to allow optimum coupling efficiency, which is critical in high power applications. A unique feature of the adjustable focus connector design is that one can adjust the distance the ferrule and fiber protrudes from the connector housing. The connector also has a built-in residual spring mechanism that allows one to safely connect two fibers together. Our engineers have extensive working knowledge with both continuous output (CW) and pulsed laser applications and can help you select the best system for your application. Please contact AMS Technologies for further assistance. Key Features: Operating Wavelengths 200 to 2000 nm SM Fibers Unique Connector Design for Precise Fiber to Fiber Coupling Minimizes Thermal Damage Able to Withstand Temperatures up to +500 °C Compatible with SMA905 and FC Connectors Different Fiber Endface Finishes Available for Higher Power Applications Stainless Steel Armored Cabling for Maximum Safety High Power Anti-reflection Coatings Available Applications: Laser Marking, Cutting and Welding; Materials Processing; High Power Spectroscopy; Non-linear Optics; Laser Surgery; Light Detection and Ranging (LIDAR)