Skip to main content

NOA 72 Optical Adhesive 10g syringe

Product information "NOA 72 Optical Adhesive 10g syringe"

Refractive Index 1.6; 155 cps Viscosity at 25°C

Norland Optical Adhesive 72 ("NOA72 10g syringe")is an optically clear, liquid adhesive that will cure when exposed to either long wavelength ultraviolet light or visible light. This one part,low viscosity adhesive is 100% solids and offers advantages in optical bonding applications. The use of NOA 72 eliminates premixing, drying or heat curing operations common to other adhesive systems.

NOA 72 is recommended for bonding plastics such as acrylic, polycarbonate, cellulose acetate butyrate or glass where low UV light transmission prevents curing of other adhesives. Typical applications would be bonding of compound lenses, laminating polarized film between glass or plastic or bonding leaded glass.

NOA 72 is cured by ultraviolet light between 315 to 400 nanometers and visible light between 400 to 450 nanometers. The peak absorption wavelengths are 320, 365 and 420 nm. Full cure requires 5 Joules/sq. cm of energy between 315 and 450 nm.

Typical Properties of NOA 72

Hardness - Shore D 75
Dielectric Constant at 1 MHz 3.98
Dielectric Strength (V/mil) 456
Dissipation Factor at 1 MHz .0351
Volume Resistivity (ohm/cm) 7.37 x 10 to the 14 power
Surface Resistivity (ohm) 3.73 x 10 to the 12 power


Shelf life of the liquid is a minimum of 4 months from the date of shipment, refer to the package label for the actual expiration date, if stored in a cool (5-22° C), dark place in the original container.If refrigerated, allow the adhesive to come to room temperature prior to use.

Manufacturer "Norland"
Related links of the manufacturer

Similar products

Adhesives for Fiber Array Assemblies
Viscosity 70->20,000 mPas; Shear Bond Strength > 69->200 kgf/cm²; Bending Adhesion Strength 9-25 kgf/cm²; UV Curing Conditions 10-100 mW/cm², 5, 10 min; Colour Light Yellow, Colourless, White; Tg +42-+219 °C NTT-AT’s series of adhesives for fiber array assemblies feature high moisture resistance and excellent workability for v-groove fixing or optical fiber fixing. Fiber arrays are used for the input and output of optical waveguide devices. NTT-AT’s AT3925M, AT9390, AT9968, AT3727E and AT3728E epoxy-based optical adhesives are used for fixing the v-grooves and have realized price reductions while enhancing moisture resistance compared to conventional products. These adhesives can be polished after assembly. NTT-AT’s AT9575M (epoxy) and AT8105 (acrylate) adhesives for optical fiber fixing have gained popularity for their good workability as non-fluid adhesives. NTT-AT has executed durability tests that have shown no peeling of a fiber array after 2,000 hours at +85 °C and 85% of humidity. With viscosities that are appropriate for the usage location, the adhesives for fiber array assemblies are easy to use. While the adhesives for fixing v-grooves show fluidity, the optical fiber fixing adhesives’ consistency is that of a paste, suitable for protecting the fiber. In case you need any consulting regarding issues related to adhesion, please contact the AMS Technologies optical adhesives experts to discuss the detailed challenges of your application. Key Features: Excellent Durability Just the Right Viscosity for Easy Application: Non-liquid Viscosity for Fiber Fixation, Low Viscosity Fluid for Fiber Fixation into V-Type Groove Heat-proof: Maximum Glass Transition Temperature Tg of Over +200 °C (AT3925M) Viscosity: 70 to >20,000 mPas Shear Bond Strength: > 69 to >200 kgf/cm² Bending Adhesion Strength: 9 to 25 kgf/cm² UV Curing Conditions: 10 to 100 mW/cm², 5, 10 min Colour (Pre-Curing): Light Yellow, Colourless, White Glass Transition Temperature Tg: +42 to +219 °C Applications: Gluing of Fiber Array Assemblies; V-Groove Fixing; Optical Fiber Fixing
Product number: SW11651
Manufacturer:
Adhesives for Optical Waveguides
Refractive Index 1.458-1.567; Viscosity 145-2,000 mPas; Optical Transmittance (@1 mm, 1.3 µm) 82%-94%; Bond Strength 99->247 kgf/cm²; UV Curing Conditions 10, 30 mW/cm², 5, 10 min You are looking for PLC and fiber array adhesion with high reliability? Try NTT-AT’s series of adhesives for optical waveguides! Within this series you find acrylate-based adhesives (AT6001, AT8224)with excellent durability that have cleared a large number of reliability tests. Epoxy adhesives are also part of this series, with a refractive index that can be accurately controlled within a range of 1.456 to 1.567 (±0.005, Na-D) – or with a fixed refractive index that is the same as quartz to deliver low reflectance (GA700L, GA700H). UV curing of the adhesives for optical waveguides allows for adhesion in a short time frame and makes alignment easy. The adhesives withstand a solder reflow process for Si Photonics (+260 °C). In order to achieve high reliability, a product must clear the tests conducted by the users themselves. If you have had even just a bit of dissatisfaction in reliability test results in the past, please put NTT-AT’s adhesives for optical waveguides to the test. In case you need any consulting regarding issues related to adhesion, please contact the AMS Technologies optical adhesives experts to discuss the detailed challenges of your application. Key Features: Optical Adhesive Used for PLC to Fiber Link-up Precision Refraction Index of 1.458 to 1.567 (±0.005, Na-D) Provides Controllability Ultraviolet (UV) Curing Conditions: 10, 30 mW/cm², 5, 10 min Very Little Adhesion Loss Due to Heat or Moisture, Providing High Durability Viscosity: 145 to 2,000 mPas Optical Transmittance: 82% to 94% (@1 mm Thickness, Wavelength 1.3 µm) Bond Strength: 99 to >247 kgf/cm² Applications: Gluing of Optical Waveguides; PLC to Fiber Link-up; Silicon Waveguide to Fiber Link-up
Product number: SW11650
Manufacturer:
Epo-Tek 353ND Epoxy, 2g PE353ND-2G
Piranha EPO-TEK® 353ND Epoxy, 2 gramsTwo component, 100% solids, heat curing epoxy designed for high temperature applications. It will perform continuously at 200°C while also tolerating 300-400°C for several hours. Recommended cure time and temperature: 110°C for 30 minutes. Pot life of up to 3 hours.
Product number: C007015-6
Manufacturer:
Epo-Tek 353ND Epoxy, 4g PE353ND-4G
Piranha EPO-TEK® 353ND Epoxy, 4 gramsTwo component, 100% solids, heat curing epoxy designed for high temperature applications. It will perform continuously at 200°C while also tolerating 300-400°C for several hours. Recommended cure time and temperature: 110°C for 30 minutes. Pot life of up to 3 hours.
Product number: C014339-6
Manufacturer:
High Refractive Index Optical Adhesives
Refractive Index 1.603-1.720; Viscosity 9-7,000 mPas; Transmittance 72%-96%; Hardness 67-83 Shore D; Shear Bond Strength 35->280 kgf/cm²; UV Curing Conditions 10, 100 mW/cm², 5, 10 min; Tg +63-+113 °C With a typical refractive index of 1.5 in conventional optical adhesives, the problem of a high reflection loss arose in cases of adhesion with high refractive index glass and crystal materials. Utilizing its refractive index control technology and optical loss reduction technology, NTT-AT has developed optical adhesives with a high refractive index adjustable to 1.6 or more. By adding high refractive index fillers, NTT-AT is even able to manufacture resins with a refractive index of 1.9. These resins are aimed at usage in the fields of optical recording, display technology, optical energy uses, etc. In addition to this series, NTT-AT also provides high refractive index resins for nanoimprint applications. NTT’s high refractive index resins are excellent in transparency in visible light domains, with haze values of 1 or less, so it is expected that they are used as a coating agent for displays and similar products. Within this series, you find acrylate-based adhesives (#18165 and #6205) as well as epoxy adhesives (E3754 and E7200). To match the particular working environment of our customers, NTT-AT provides both ultraviolet (UV) and heat curing types. NTT-AT provides refractive index customized resins to meet each customer's needs. It is possible to respond to several kinds of requests such as with/without solvent or adjusting the viscosity. Please contact the AMS Technologies optical adhesives experts to discuss your customized refractive index matched optical adhesive solution. Key Features: Refractive Index of 1.6 or More Can Be Chosen High Accuracy of Refracting Index Control: ±0.005 Choice of Either Ultraviolet (UV) Curing or Heat Curing Method High Transparency in Visible Light Domains: Optical Transmittance 90% or More at 1 mm Thickness Refractive Index: 1.603 to 1.720 Viscosity: 9 to 7,000 mPas Transmittance: 72% to 96% Hardness: 67 to 83 Shore D Shear Bond Strength: 35 to >280 kgf/cm² UV Curing Conditions: 10, 100 mW/cm², 5, 10 min Glass Transition Temperature Tg: +63 to +113 °C Applications: High Refractive Index Coating Agents; Bonding High Refractive Index Crystal Materials; Bonding High Refractive Index Glass (for Camera Lenses, Eyeglass Lenses, etc.); Higher Efficiency Optical Input and Output Power; Efficient Conversion of Light Energy; Optical Recording; Display Technology
Product number: SW11655
Manufacturer:
High-Precision Optical Adhesives
Viscosity 36,000, 180,000 mPas; Bending Adhesion Strength >114, >128 kgf/cm²; UV Curing Conditions 100 mW/cm², 2 min; Curing Shrinkage Rate 0.5%, 0.9%; Tg +195, +233 °C; Thermal Expansion Coefficient 18, 20 ppm/°C NTT-AT’s high-precision optical adhesives allow easy fixation of optical components with sub-micron accuracy. Based on epoxy, these high-precision optical adhesives are available with low viscosity of 36,000 mPas (AT3916P) or with high viscosity of 180,000 mPas (AT3862P). Both adhesives show minimal position changes due to curing time and temperature. Shrinkage rate during curing is very low for this series of high-precision optical adhesives, and the thermal expansion coefficient is small. Using ultraviolet (UV) ray curing makes alignment easy. NTT-AT’s series of high-precision adhesives show excellent durability: Even after a high-temperature process at +260 °C, the adhesives’ bonding strength does not change. And no peeling occurred after 200 cycles in a simplified heat cycle test. In order to achieve high reliability, a product must clear the tests conducted by the users themselves. If you have had even just a bit of dissatisfaction in precision or durability results in the past, please put NTT-AT’s high-precision adhesives to the test. In case you need any consulting regarding issues related to adhesion, please contact the AMS Technologies optical adhesives experts to discuss the detailed challenges of your application. Key Features: Low Shrinkage Rate During Curing: 0.5% (AT3862P), 0.9% (AT3916P) Low Thermal Expansion Coefficient: <20 ppm/°C Ultraviolet (UV) Curing for Easy Alignment Excellent Durability: No Change in Bonding Strength After +260 °C High-temperature Process, No Peeling After 200 Heat Test Cycles Viscosity: 36,000, 180,000 mPas Bending Adhesion Strength: >114, >128 kgf/cm² UV Curing Conditions: 100 mW/cm², 2 min Glass Transition Temperature Tg: +195, +233 °C Applications: High-precision Fixation of Optical Components With Sub-micron Accuracy
Product number: SW11652
Manufacturer:
Index Matching Liquid IML 150 (1oz bottle)
Refractive Index 1.52; 100 cps Viscosity at 25°CNorland Index Matching Liquid 150 is a low viscosity liquid monomer that can be used as an index matching media for temporary splicing using the Norland Optical Splice. This material will not cure and will always remain a liquid. Typical Properties of Norland Index Matching Liquid 150 Appearance Light yellow liquid Normal index matching silicone fluids and gels can cause adhesion problems because once it contacts a surface it is very difficult to remove all traces. Our IML 150 can be removed with acetone.
Product number: C007048-6
Manufacturer:

€34.68*

Customers also bought

NOA 61 Optical Adhesive 10g syringe
Refractive Index: 1.56; 300 cps Viscosity at 25°CNOA 61 strong, heat resistant optical adhesive with refractive index 1.56 and curing between 320 - 380 nm UV light MIL-A-3920 compliant (10g syringe)
Product number: C007060-6
Manufacturer:

€24.47*
46P-9-5D Polishing Film
5 inch Disc; Grit 9 µm; Silicon Carbide; Stainless Steel and Ceramic Ferrule; no PSA The 46P-9-5D fiber optics polishing film from Nanolap comes in a pack that contains 10 pieces.
Product number: C007162-6
Manufacturer:

€1.15*
NOA 75 Optical Adhesive 10g syringe
Refractive Index 1.52; 80-95 cps Viscosity at 25°C Norland Optical Adhesive 75 (10g syringe) is a clear, colorless, liquid photopolymer that will cure when exposed to ultraviolet light. Since it is a one part system and 100% solids, it offers many advantages in bonding where the adhesive can be exposed to UV or visible light. The use of NOA 75 eliminates premixing, drying or heat curing operations common to other adhesive systems. Curing time is remarkably fast, and is dependent upon the thickness applied and the amount of ultraviolet light energy available.NOA 75 is designed to give the best possible optical bond when using plastic to plastic or plastic to glass substrates. NOA 75 has excellent adhesion to cellulose acetate butyrate (CAB) and glass and good adhesion to CR-39, polarizedfilm, nylon, polyester film, polycarbonate and acrylics.Typical Properties of NOA 75 Solids 100% Color Slight yellow tint Hardness - Shore D 25 Water Absorption (ASTM D 570-63) .0.86%/48H Modulus PSI 2610 Tensile Strength PSI 164 Elongation at failure 7% Shelf life of the liquid is at least 4 months from the date of shipment if stored in a cool (5-20C), dark place in the original container. If refrigerated, allow the adhesive to come to room temperature prior to use.
Product number: C007094-6
Manufacturer:

€24.47*
NOA 78 Optical Adhesive 10g syringe
Refractive Index 1.50; 8000-11000 cps Viscosity at 25°C Norland Optical Adhesive 78 (10g syringe) is a clear, colorless, liquid photopolymer that will cure when exposed to ultraviolet light or visible light (blue-violet). Since it is a one part system and 100% solids, it offers many advantages in bonding where the adhesive can be exposed to UV light. The use of NOA 78 eliminates premixing, drying or heat curing operations common to other adhesive systems. Curing time is remarkably fast, and is dependent upon the thickness applied and the amount of ultraviolet light energy available.NOA 78 is designed to give the best possible optical bond when using plastic to plastic or plastic to glass substrates. NOA 78 has excellent adhesion to CR-39, polarized film, Delrin®, nylon, cellulose acetate butyrate, polycarbonate and acrylics.Typical Properties of NOA 78 Color Slight yellow tint Modulus (psi) 1140 Tensile (psi) 649 Elongation at failure 57% Hardness - Shore D 55 Dielectric Constant at 1 MHz 4.87 Dissipation Factor at 1 MHz .0.092 Volume Resistivity (ohm/cm) 22 x 10 to the 15 power Surface Resistivity (Megohms) 2.05 x 10 to the 12 power Dielectric Strength (volts) 624  NOA 78 can withstand temperatures from -20C to 60C.Shelf life of the liquid is at least 4 months from the date of shipment if stored in a cool (5-20C), dark place in the original container. If refrigerated, allow the adhesive to come to room temperature prior to use.
Product number: C007084-6
Manufacturer:

€24.47*
NOA 71 Optical Adhesive 10g syringe
 Refractive Index 1.56; 200 cps Viscosity at 25°C Norland Optical Adhesive 71 ("NOA71") is an optically clear, liquid adhesive that will cure when exposed to long wavelength ultraviolet light (10g syringe). The adhesive is a one-part, 100% solids material that offers advantages in bonding applications that require optical clarity or require fast cure times and long term stability over a wide range of temperatures. The use of NOA 71 eliminates premixing, drying, or heat curing operations common to other adhesive systems.NOA 71 was formulated to provide a strong bond to glass surfaces. This adhesive can also be used for adhering to other substrates, such as metal, fiber- glass, and glass filled plastics. Typical applications are laminating solar cells, holographic plates, flat panel displays and touch screens or as a clear coating on plastic or metal.NOA 71 is cured with long wavelength UV light from 315 to 400 nanometers with peak absorption at 365 nm. The amount of energy required for full cure is 3.5 Joules/sq. cm of UV light. Typical Properties of NOA 71 Solids 100% Elongation at Failure 43% Modulus of Elasticity (psi) 55,000 Tensile Strength (psi) 1,300 Hardness - Shore D 86 Dielectric Constant (1 MHz) 4.0 Dielectric Strength (V/mil) 456 The shelf life of NOA 71 liquid is at least 4 months from the date of shipment if kept in a cool (5-22° C), dark place in the original container. If refrigerated, allow the adhesive to come to room temperature prior to use.
Product number: C007090-6
Manufacturer:

€24.47*
NOA 85V optical adhesive 1oz bottle
Viscosity at 25°C 200 cps, Refractive Index 1.46 Norland Optical Adhesive NOA 85V is a clear, colorless, liquid photopolymer that will cure when exposed to ultraviolet light and or visible light (blue-violet). Since it is a one part system and 100% solids, it offers many advantages in bonding where the adhesive can be exposed to UV light. The use of NOA 85V eliminates premixing, drying or heat curing operations common to other adhesive systems. Curing time is remarkably fast, and is dependent upon the thickness applied and the amount of ultraviolet light energy available.NOA 85V is designed to give the best possible optical bond when using plastic to plastic or plastic to glass substrates. NOA 85V has excellent adhesion to CR-39, polarized film, Delrin®, nylon, cellulose acetate butyrate, polycarbonate, acrylics and glass. NOA 85V also has excellent clarity, low shrinkage and a slight flexibility that make it superior to other materials for optical bonding. These characteristics are important in order for the user to produce high quality optics and achieve long term performance under changing environments.NOA 85V is cured by ultraviolet light with maximum absorption within the range of 320-400 nanometers and visible light between 400 and 450 nanometers. The peak absorption wavelengths are 325, 365 and 405 nanometers. The recommended energy required for full cure is 3.5 Joules/cm squared.Typical Properties of NOA 85V Temperature Range -15°C to 90°C Elongation at Failure 111% Modulus of Elasticity (psi) 9,340 Tensile Strength (psi) 1,500 Hardness - Shore D 40 Shelf life of the liquid is a minimum of 4 months from the date of shipment, refer to the package label for the actual expiration date, if stored in a cool (5-22° C), dark place in the original container. If refrigerated, allow the adhesive to come to room temperature prior to use.
Product number: C007096-6
Manufacturer:

€57.13*