Stainless Steel Tubes Fin Heat Exchanger AMS-229x409x66-2-20-SS-AL

230W @ 20°C; >2 lpm @ 14 psig; 1/4" valved CPC Fittings; Centrifugal Pump; Aluminium and Polymers This thermoelectric recirculating chiller is a low-cost, high-performance device optimized for lasers, optics and life sciences. It features precise temperature control (±0.05°C repeatability), long-life reliability, quiet operation and environmental friendliness in a compact size. Using universal power, the TEC chiller is very energy efficient only drawing power when required.

Refractive Index 1.315; 15 cps Viscosity at 25°C Norland Optical Adhesive 1315 is clear liquid adhesive that will cure when exposed long wavelength ultraviolet light. NOA 1315 is recommended for bonding for glass to glass. Adhesion is also good to cellulose acetate butyrate. NOA 1315 is cured by ultraviolet light between 320 to 450 nm. Full cure requires 6 Joules/cm 2. The adhesive exhibits oxygen inhibition when used exposed to air. To overcome this the adhesive must be cured under an inert atmosphere, such as nitrogen. When used as a coating the liquid adhesive's temperature must be kept below 9C to prevent vaporization.Typical Properties of NOA 1315 Temperature Range -15°C to 90°C Keep NOA 1315 in a cool ( 5 to 20°C) dark place. If refrigerated, allow the adhesive to come to room temperature before using.

Vapor Compression Chiller; 450W @+25°C; 230VAC; 2lpm; USB/ Ethernet; Benchtop Key Features: Miniature Recirculating Water Chiller Compact Size, Easy to be Integrated in Customer Application User-Definable PID Parameters and Fan Velocity Calm Operation With Low Vibration and Noise Ideal for Water Cooling Tasks up to 450 W IoT Ready: Remote Operation, Monitoring and Service over Integrated Ethernet Interface Full chiller power in a shoebox form factor: the mRC-C-450-100/240 mini recirculating chiller provides to 450 W cooling capacity and contains a compressor-based refrigerant circuit as well as a closed, recirculating coolant (water) circuit that is pressurized – all that in a compact, 350 x 290 x 230 mm housing. This small size is enabled by utilizing a miniature rotary compressor, customized miniature evaporator and condenser. On the coolant side, pressurizing the circuit allows a very small tank, and a compact centrifugal pump also contributes to reduced space requirements. Due to the speed-controlled compressor, the mRC-C-450-100/240 chiller offers low vibration and noise throughout the compressor’s BLDC speed range. Further features are automatic fill and drain of the coolant circuit, global operability due to a universal 90 to 264 VAC power supply, and an integrated Ethernet interface allowing remote operation, monitoring and service. Specifications: Cooling Capacity: 300 W (Twater = +20°C, Tambient = +40°C) to 500 W (Twater = +20°C, Tambient = +20°C) Temperature Stability: +2/-1.5 K Over-/undershoot at 250 W Heat Load ON/OFF, Down to 0.05 K Continuous Operation Available Pressure Head: 1.5 bar @1 lpm; 0.5 bar @5.5.lpm Noise Level: 63 dBA (fan 40%, compressor 100%) Control: Local, USB/Serial, Internet (Web Browser) via Ethernet (IoT Ready) Interlock I/O Alarms: Liquid Level, Tank Pressure, Coolant Feed Temperature, Coolant Flow Rate, Condenser Pressure Power Supply: 90 to 264 VAC, 24 VDC Derivative Available on Demand Power Consumption: <300 W Dimensions: 350 x 280 x 230 mm, Main Body Without Filter Weight: 13 kg Approval: CE Applications: Water Cooling of Lasers and Other Applications; Integration of Water Cooling Capabilities in Systems with Limited Space  

Refractive Index 1.524; 1200 cps Viscosity at 25°C Norland Optical Adhesive 65 ("NOA65") is a clear, colorless, liquid ph2otopolymer that will cure when exposed to ultraviolet light. Since it is a one part system and 100% solids, it offers many advantages in bonding of optical materials where the bonding surface can be exposed to light. The use of NOA 65 eliminates premixing, drying and heat curing operations common to other optical adhesive systems. Curing time is remarkably fast, and is dependent upon the thickness applied and the amount of ultraviolet light energy available. The cured adhesive is very flexible and was designed to minimize strain. NOA 65 is especially suitable where the adhesive cross section would be relatively thick. NOA 65 has enough elasticity to keep strain to a minimum even when dissimilar materials with different coefficients of expansion are bonded together. Typical applications would be potting of lenses in metal mounts, bonding plastic to glass and cold blocking. Typical Properties of NOA 65 Solids 100% Elongation at Failure 80% Modulus of Elasticity (psi) 20,000 Tensile Strength (psi) 1,500 Hardness - Shore D 50 Temperature Range -15 to 60° C   Shelf life of the liquid is at least 6 months from the date of shipment if stored in a cool (5-22° C), dark place in the original container. If refrigerated, allow the adhesive to come to room temperature prior to use.

Copper Fins; Stainless Steel Tubes; 148.3x139.6x46.5 mm; 6-pass; 60 barWater-to-air heat exchangermain dimensions HX housing: 148,3 mm x 139,6 mm x 46,5 mmTubes and tube connections: stainless steel 316L, OD 3/8"Connection tube length 53 mm6 pass, return-bends weldedCorrugated copper fins; thickness 0,12 mm; 18 fpiHX housing and end plates: stainless steel 304/316LHX housing including fan mount, with M4 cage-nuts/press-nutsSpecified fluid pressure: max. 60 bar 

Refractive Index 1.315; 15 cps Viscosity at 25°CNorland Optical Adhesive 1315 is clear liquid adhesive that will cure when exposed long wavelength ultraviolet light. NOA 1315 is recommended for bonding for glass to glass. Adhesion is also good to cellulose acetate butyrate. NOA 1315 is cured by ultraviolet light between 320 to 450 nm. Full cure requires 6 Joules/cm 2. The adhesive exhibits oxygen inhibition when used exposed to air. To overcome this the adhesive must be cured under an inert atmosphere, such as nitrogen. When used as a coating the liquid adhesive's temperature must be kept below 9C to prevent vaporization.Typical Properties of NOA 1315Temperature Range-15°C to 90°CKeep NOA 1315 in a cool ( 5 to 20°C) dark place. If refrigerated, allow the adhesive to come to room temperature before using.

Thermoelectric Cooler DRIFT-1.5 Size : 40 x 40 x 4,1 mm Sealing : Epoxy High Temperature : 120° Wire length : 200 mm