DBR Single Frequency Laser Diodes

Product number: SW10679

Manufacturer: TOPTICA eagleyard

Downloads

DBR Single Frequency Laser Diodes Toptica eagleyard Datasheet

Product information "DBR Single Frequency Laser Diodes"

632, 633 nm; Typ. Linewidth 1.0 MHz; Max. Output Power 10 mW CW; Threshold Current ≤120 mA; Slope Efficiency 0.4 W/A; Side Mode Suppression Ratio ≥30 dB

Toptica eagleyard’s DBR series of distributed Bragg grating (DBR) laser diodes contains a multi-section laser with gain, phase and distributed feedback (DFB) sections. DBR series laser diodes feature a built-in wavelength-selective grating stabilizing the wavelength

The DBR series’ resonator comprises a periodic structure. Thus, the devices operate on a single resonator mode emitting quasi-monochromatic radiation with a very small line width and low phase noise. The lasers can have very low-intensity noise because of the lack of mode partition noise. Due to the Gaussian mode the output is diffraction-limited..

Special variants are available, especially suitable for spectroscopy with mode‐hop free operation and small linewidth guaranteed at the specified target wavelength for spectroscopic applications – these laser diodes are reaching the target wavelength by temperature tuning and allow wavelength tuning around this target wavelength.

Key Features:

Center Wavelength: 632 nm, 633 nm
Narrow Linewidth: Typ. 1.0 MHz
Threshold Current: ≤120 mA
High Side Mode Suppression Ratio: ≥ 30 dB
Max. Output Power: 10 mW CW
Max. Forward Current: 160 mA
Including Monitor Diode, TEC Cooler and Thermistor
Package: Hermetic 14-pin Butterfly

Applications: HeNe Laser Replacement; Spectroscopy; Metrology; Sensing

Manufacturer "TOPTICA eagleyard"

TOPTICA eagleyard started as a spin-off from the Ferdinand-Braun Institut (FBH) in 2002. The core competence is the development, production and sale of innovative high-power laser diodes based on GaAs (Gallium Arsenide). Its portfolio contains laser diodes with wavelengths ranging from 630 nm to 1120 nm (DFB-lasers, tapered lasers, ridge waveguide lasers and broad area lasers). These laser diodes are addressing a variety of applications such as aerospace and defense, spectroscopy, medical instrumentation, test & measurement and material analysis.

Customers also viewed

AutoStrip II Window Stripping Unit

Automated, Mid-span; Window Strip Length 2-150 mm; Fiber Coating Diameter ≤1,000 µm; Fiber Cladding 125-400 µm; Pulling Speed 20-100 mm/min The AutoStrip II is designed for fast, chemical free window stripping of optical fibers. Utilizing SAE Technologies’ patented “Burst Technology™”, this system accomplishes the often difficult task of window stripping fibers with acrylate coating diameters up to 1,000 µm. The AutoStrip II automated, mid-span window stripping unit meets the need for variable window strip lengths at high strength and ultra cleanliness. The proven Burst Technology™ method instantly vaporizes the fiber coating. The result is a clean, stripped fiber at substantially higher strength than any mechanical stripping method. The fiber is free of debris at 400x magnification. Equipped with a built-in, high-force fiber tensile tester, the AutoStrip II system can pull the fiber up to 20 N (235 kpsi). To ensure high quality, repeatability and high production yield, all critical processes and parameters such as stripping distance, burst temperature, burst speed, and strength test are controlled automatically by a built-in microprocessor. The AutoStrip II can be used as a stand-alone unit or integrated into different sub-systems. The use of chemicals for high-strength fiber stripping is now a thing of the past! Key Features: Chemical-Free (No Cleaning or Stripping Chemicals Required) Easy, Low-maintenance Bench-top Design Fast Cycle Time & High First-pass Yield Accommodates Acrylate Coating Fiber Diameters up to 600 μm (Custom Nozzles up to 1,000 μm) Variable Window Strip Lengths From 2 up to 150 mm Fiber Cladding: 125 to 400 μm Fiber Strength: Typical >35 N on 125 μm Fiber Fiber Cleanliness: Free of Debris at 400x Magnification Built-in High-force Linear Tensile Tester, Tensile Strength: 0 to 20 N Pulling Speed: 20 to 100 mm/min, Hold Time: 0 to 5 s Power Supply: 115 to 230 V AC Compressed Air: External Compressor, 95 psi - 5 SCFM Flow PC Interface: RS232C Software-adjustable Parameters Automated Fiber Clamps Built-in Graphical LCD Control Storage of up to 10 Programs Dimensions: 465 x 315 x 225 mm Application: Automated, Mid-span Window Stripping of Optical Fibers With Acrylate Coating Diameters up to 1,000 µm

Product number: SW11249

Manufacturer: