RC SMF Special SM Fiber

Plastic; High Power Internal Fitting Float Switches The RSF30 Float Switch series is a range of higher power side entry, internally fitted devices. These may be used for directly switching some small loads of less than 100VA.Mounting of this series requires access to the inside of the tank. They are manufactured in Nylon or Polypropylene, with a choice of gasket materials, to suit most commonly used liquids. The switch action may be reversed by rotating the device through 180¡.

850, 1060, 1300 nm; Core Dia. 50 µm; Cladding Dia. 125 µm; Acrylate Coating; Optional Hermetic Layer; -60 to +180 °C Equipped with mid-temperature acrylate-based coatings, the Corning® ClearCurve® series of multi mode (MM) bend insensitive optical fibers now includes higher temperature and higher bandwidth capability. For use at temperatures up to +180 °C and beyond, these acrylate-based fibers deliver incredible macro bend performance with ease of use and handling – benefiting sensing systems operating in harsh environments.. The ClearCurve multi mode fiber series includes the MM50BI-XMT fiber with mid-temperature acrylate coating as well as the MM50BIH-XMT fiber with mid-temperature acrylate coating and an additional hermetic layer. For mid-temperature single mode fibers please refer to Corning’s ClearCurve single mode fiber series. Key Features: Acrylate-base for Ease of Handling Rated for up to +180 °C Test data available at +200 °C Higher Bandwidths available Hermetic Coating (Optional) for Protection Against Hydrogren-induced Attenuation Increase and Improved Fatigue Resistance Consistent Strength Over Time at Elevated Temperatures Designed to Meet Your Specific Needs: Recommended Min. Bending Radius of 7.5 mm Fully Compliant With ITU-Recommendations G651.1 Compatible with Current Optical Fibers and Practices Applications: Fiber Sensing and Data Transmission with Tight Bend Requirements and/or High Bandwidth Requirements for: Aerospace & Defense, Structural Health Monitoring, Down-Hole Drilling

1310, 1550 nm; Mode Field Dia. 8.6, 9.65 µm; Cladding Dia. 125 µm; Acrylate Coating; Optional Hermetic Layer; -60 to +180 °C  Equipped with mid-temperature acrylate-based coatings, the Corning® ClearCurve® series of single mode (SM) bend insensitive optical fibers now includes higher temperature capability. For use at temperatures up to +180 °C and beyond, these fibers deliver the best macro bend performance in the industry with ease of use and handling – benefiting sensing systems operating in harsh environments. The ClearCurve single mode fiber series includes the SMBI-5-XMT fiber with mid-temperature acrylate coating as well as the SMBIH-5-XMT fiber with mid-temperature acrylate coating and an additional hermetic layer. For mid-temperature multi mode fibers please refer to Corning’s ClearCurve multi mode fiber series. Key Features: Acrylate-base for Ease of Handling Rated for up to +180 °C Test data available at +200 °C Hermetic Coating (Optional) for Protection Against Hydrogren-induced Attenuation Increase and Improved Fatigue Resistance Consistent Strength Over Time at Elevated Temperatures Designed to Meet Your Small Bend Needs: Recommended Min. Bending Radii of 5 mm Fully Compliant With ITU-Recommendations G.657 and G652.D Compatible with Corning® SMF-28e® and SMF-28e+® Fibers Applications: Fiber Sensing and Data Transmission with Tight Bend Requirements for: Aerospace & Defense, Medical, Structural Health Monitoring, Down-Hole Drilling

High-speed, Portable Polisher for Field Assembly; Connector/Ferrule Type SC, MU, FC, LC, MT, MTRJ, Custom; Radius of Curvature 10 to 25 mm; Apex Offset <50 µm; Return Loss >50 dBNTT Advanced Technology Corporation’s POP-311 series of high-speed portable polishers is suitable for installing optical connectors or extending optical fibers at field work site. Its cylinder jig allows for on-site polishing / re-polishing of MPO connectors and single fiber connectors.High polishing quality equivalent to that of factory use polishers can be achieved. The POP-311 high-speed portable polishers are able to polish connectors at very high velocity – up to 700 revolutions per minute. The POP-311 series is also suitable for re-polishing of MT connectors. When optical fiber connectors due to be laid are found to be damaged, on the spot repolishing makes them ready to be used. Also, LC-Duplex connectors can be simultaneously polished without dismantling.With only three to five processes, polishing MPO connectors and single fiber connectors can easily be done on location. For example, the polishing procedure from adhesive removal to advanced PC polish takes about 150 seconds (SC connector/terminal), while advanced PC polish by re-polishing takes only about 50 seconds (SC connector/terminal). Applicable connectors/ferrules are SC, MU, FC, LC, MT and MTRJ type optical connectors and glass ferrules. A broad range of attachments is available for the various different connector types. Since the attachments are the same as for the factory use ATP-3000 polishing machine, they can be used for a wide range applications such as MPO connectors and single fiber connectors (UPC/APC), and polishing of all types of capillaries and fibers. Widely accessible rechargeable nickel hydride battery (AA) or alkaline dry battery (AA) can be used as power supply.Key Features:Suitable for MT, MTRJ, SC, MU, FC and LC ConnectorsHigh Quality- Battery OperatedHigh Speed PolishingApplications: Optical Connector Polishing (for re-polishing and new polishing processes)