HTC Series TEC Temperature Controllers
Product number:
SW10822
Product information "HTC Series TEC Temperature Controllers"
Output Current TEC ±1.5, ±3, ±4 A; PCB Mount; Supply Voltage 5-12 VDC; Temperature Stability 0.0009°C
With its advanced and reliable circuitry, Wavelength Electronics’ HTC series of component type TEC temperature controllers achieves 0.0009°C temperature stability. Its low-profile package is ideal for designs with space constraints and can be mounted in a number of different ways. The HTC can be electrically connected to a PCB or by using a SIP connector and cable. The heatsink can be bolted directly to the HTC series device, or the device can be bolted directly to the equipment chassis to maximize space efficiency.
The ultra-stable linear, PI control loop offers maximum stability, while the bipolar current source has been designed for higher efficiency.
The HTC series drives up to ±4.0 A for either thermoelectrics (bipolar) or resistive heaters (unipolar). Three maximum output current ranges are available: ±1.5, ±3 and ±4 A. While regular drivers for 1.5 and 3 A are designed for 0.031 inch (0.79 mm) thick printed circuit boards (PCBs), each of the models (including drivers for 4 A) is also available as a “HTCxxoo-62” variant, suitable for mounting on 0.062 inch (1.57 mm) thick PCBs.
The HTC Series TEC temperature controllers are easily configured for any design. Virtually any type of temperature sensor can be used with the HTC, and a built-in sensor bias current source simplifies use with resistive temperature sensors. The independently adjustable proportional gain (P) and integrator time constant (I) can be modified to optimize temperature overshoot and stability.
Other features offer added flexibility. A single resistor sets the maximum output current to load. Add a diode to operate resistive heaters with a unipolar output current. An onboard reference voltage simplifies potentiometer control of the temperature setpoint. You can also choose to operate remotely with an external setpoint voltage. Two monitor pins provide access to the temperature setpoint voltage and the actual sensor voltage.
Free, effective and responsive technical support is available to simplify integration of Wavelength products into your OEM design. Standard products can be easily modified to meet your application requirements. Get in touch with the AMS Technologies TEC Temperature Controllers experts to discuss your customized solution!
Key Features:
- Component Type, SIP PCB Mounting
- 20-pin SIP Size: 41 x 67 x 8.6 mm
- Compatible With 0.031 or 0.062 in Thick PCBs
- Drive up to ±4 A of TEC or RH current
- +5 to +12 V Single Supply Operation (up to +30 V Operation on Request)
- Maximum Power Dissipation: 17 W
- Supports Thermistors, RTDs, IC Sensors
- Adjustable Sensor Bias Current
- Linear Temperature Stability: 0.0009 °C
- Stability Across Ambient: 0.002 °C (10 kΩ Thermistor at + 25°C) Over 1 h – Ideal for Scanning Applications
- PI Controller Minimizes Overshoot and Time to Temperature
- Adjustable Sensor Bias Current Optimizes Sensor Feedback Voltage
- Can Operate With Unipolar Current for Resistive Heaters
- Heat and Cool Current Limits
- Monitor Actual and Setpoint Temperatures
Applications: Particularly Suited to Applications Where Temperature is Scanned Across Ambient, Like Medical, Defense, Communications, Manufacturing and More
Manufacturer "Wavelength Electronics"
Related links of the manufacturer
Similar products
1,5A Temp Controller for 0,031" PCB HTC1500
€158.03*
The advanced and reliable circuitry of the HTC Series achieves 0.0009°C temperature stability. Its low profile package is ideal for designs with space constraints. The ultrastable linear, PI control loop offers maximum stability while the bipolar current source has been designed for higher efficiency. The HTC1500 drives up to 1.5 A for either Thermoelectrics (bipolar) or Resistive Heaters (unipolar). The HTC3000 drives up to ±3 A. An evaluation board simplifies prototyping: HTCEVALPCB. A heatsink that mounts directly to the HTC is available: HTCHTSK. The HTC1500 is designed for 0.031" thick printed circuit boards (PCBs). The HTC1500-62 is designed for 0.062" thick PCBs. The HTC Series temperature controllers are easily configured for any design. Virtually any type of temperature sensor can be used with the HTC and a built in sensor bias current source simplifies use with resistive temperature sensors. The independently adjustable Proportional Gain (P) and Integrator Time Constant (I) can be modified to optimize temperature overshoot and stability.Other features offer added flexibility. A single resistor sets the maximum output current to load. Add a diode to operate resistive heaters with a unipolar output current. An onboard reference voltage simplifies potentiometer control of the temperature setpoint. You can also choose to operate remotely with an external setpoint voltage. Two monitor pins provide access to the temperature setpoint voltage and the actual sensor voltage.The HTC1500 has proven reliable in such diverse fields as medical, defense, communications and manufacturing. The HTC is particularly suited to applications where temperature is scanned across ambient.
Key Features
Compact Size - 1.5 and 3.0 A Models
Interfaces with Thermistors, IC Sensors, &RTDs
Single supply operation +5 V to +12 VDC (contact factory for higher voltage operation)
+11 V compliance with +12 V input
Stabilities as low as 0.0009°C
Temperature Setpoint, Output Current Limit, Sensor Bias, Proportional Gain, and Integrator Time Constant are User Adjustable
Monitor outputs for Temperature Setpoint and Actual Temperature
Linear Bipolar or Unipolar Output operates thermoelectrics or resistive heaters
Product number:
C008957-6
Manufacturer:
Only 2 available
1,5A Temp Controller 0,003°C temperature stability PID1500
€373.08*
The robust circuitry of the PID1500 achieves 0.003°C temperature stability. Onboard controls make this package plug and play. The linear, PI control loop offers maximum stability while the bipolar current source has been designed for higher efficiency. The PID1500 drives up to 1.5 A for either Thermoelectrics (bipolar) or Resistive Heaters (unipolar). An evaluation board simplifies prototyping: PIDEVALPCB. Heatsinking is already provided to support operation across a -20°C to +85°C operating range. The PID1500 temperature controller is easily configured for any design. Virtually any type of temperature sensor can be used with the PID1500 and a built in switchable sensor bias current source simplifies use with resistive temperature sensors. The Proportional Gain (P) is adjustable with an onboard single turn trimpot. Use an onboard trimpot to adjust the setpoint or the Analog Input pin for remote control. Use another onboard trimpot to set the maximum output current to the load or set it with a resistor between pins 1 & 2. A switch between those pins acts as a remote enable / disable. Remove a jumper to operate resistive heaters with a unipolar output current. Two monitor pins provide access to the temperature setpoint voltage and the actual sensor voltage.The PID1500 has proven reliable in such diverse fields as spectroscopy, defense, and medical research.
Key Features
Single supply operation: +5 V to +12 V
Up to 1.5 A output current available
< 0.005°C stability (24-hour)
Adjustable current limit
Remote Analog Input to adjust Temperature Setpoint
Supports Thermistors, IC Sensors, or RTDs
Temperature Setpoint, Proportional Gain, and Current Limit are user adjustable
Remotely Enable/Disable output
Can be wired for Resistive Heater control
Product number:
C001006-6
Manufacturer:
1,5A Temperature Controller for 0,062" PCB HTC1500-62
€158.03*
The advanced and reliable circuitry of the HTC series achieves 0.0009°C temperature stability. Its small, low profi le package is ideal for designs with space constraints. The linear, PI control loop offers maximum stability while the bipolar current source has been designed for higher efficiency.The HTC temperature controllers are easily configured for any design. Virtually any type of temperature sensor can be used with the HTC and a built in sensor bias current source simplifi es use with resistive temperature sensors. The independently adjustable Proportional Gain (P) and Integrator Time Constant (I) can be modifi ed to optimize temperature overshoot and stability.Other features offer added flexibility. A single resistor sets the maximum output current to your load. Add a diode to operate resistive heaters with a unipolar output current. An onboard reference voltage simplifies potentiometer control of the temperature setpoint. You can also choose to operate remotely with an external setpoint voltage. Two monitor pins provide access to the temperature setpoint voltage and the actual sensor voltage.
Key Features
Compact Size - 1.5 and 3.0 A Models
Interfaces with Thermistors, IC Sensors, & RTDs
Single supply operation +5 V to +12 VDC (contact factory for higher voltage operation)
+11 V compliance with +12 V input
Stabilities as low as 0.0009°C
Temperature Setpoint, Output Current Limit, Sensor Bias, Proportional Gain, and Integrator Time Constant are User Adjustable
Monitor outputs for Temperature Setpoint and Actual Temperature
Linear Bipolar or Unipolar Output operates thermoelectrics or resistive heaters
Product number:
C009001-6
Manufacturer:
Only 3 available
10A Chassis Mount Temp Controller PTC10K-CH
€617.17*
The PTC-CH Series Chassis Mount Temperature Controllers deliver the precision performance and long-term reliability you expect from a Wavelength Electronics temperature controller. PTC-CH Series controllers are found in such diverse applications as particle and droplet measurement, manufacturing machine vision systems, biomolecular interaction analysis, and more. They are CE certified. A PDF version of the Declaration of Conformance is available.PTC-CH controllers are available in different models so you can choose the one that best suits your application:
PTC2.5K-CH delivers up to ±2.5 A output current
PTC5K-CH for applications requiring up to ±5 A
PTC10K-CH drives up to ±10 A
PTC10K-SL can be tied to the 10 A driver to deliver a combined ±20 A output current
The PTC-CH controllers operate from a single power supply between 4.5 V and 30 V. The linear bipolar controller drives a Peltier thermoelectric cooler or a resistive heater, and the chassis-mount package integrates easily into OEM applications. PTC-CH controllers interface with a variety of temperature sensors, and the bias current is adjustable in order to maximize controller sensitivity and stability for your application. The compact chassis-mount design simplifies heatsinking and requires minimal space. PTC-CH controllers are quick to configure for your prototype project, and there are no surprises when it's time to integrate the controller into the final design. If you are using a Quantum Cascade Laser or need low noise performance with a laser diode, we offer the PTC-CH nested in the QCL OEM drivers. Information is available here. Key Features Built-in features make your product more robust to real-world operating conditions and minimize your electronics overhead:
If the optional remote temperature setpoint signal is lost, the controller defaults to a standard "safe" temperature setpoint (25ºC when a 10 kΩ thermistor is used). The safe temperature can be changed at the factory; call for details.
An on-board trimpot is used to set the output current limit to prevent over-driving the TEC, and helps protect your load from thermal runaway situations.
Proportional gain is easily adjusted with an on-board trimpot.
Low temperature coefficient design remains stable across a wide range of ambient conditions.
When used with Wavelength's laser drivers, such as the PLD Series, these temperature controllers provide stable and reliable performance that sets your system apart from your competitors' and keeps your customers satisfied.
Product number:
C008944-6
Manufacturer:
10A Temp Controller PCB Mount PTC10000
€698.92*
The PTC Series PCB-Mount Temperature Controllers are based on our long-proven PTC-CH linear controllers, and deliver the precision performance and reliability you expect from Wavelength Electronics.
PTC Series controllers are found in such diverse applications as particle and droplet measurement, communications, manufacturing test, and medical systems.The PTC controllers operate from a single power supply between 5 V and 30 V, and two models drive ±5 A or ±10 A to a Peltier thermoelectric cooler or a resistive heater. These controllers mount directly to your circuit board.
PTC controllers interface with a variety of temperature sensors, and the bias current is adjustable in order to maximize controller sensitivity and stability for your application.
You can use the PTCEVAL board to quickly confi gure the PTC controller for prototyping. Using the same controller for development and production helps guarantee there are no surprises when it's time to integrate the final design.
Key Features
Drive ±5 or ±10 A of TEC or heater current
Single supply operation: 5 to 30 VDC
Small package: 2.32" x 2.15" x 3.85"
Remote Output Enable and Temperature Setpoint controls
Short term stability of 0.0012°C (off-ambient)
Long term stability 0.002°C
Selectable sensor bias current
Adjustable current limit
PI Control with "Smart Integrator"
Failsafe Setpoint default in case of remote temperature setpoint signal error
Product number:
C008998-6
Manufacturer:
2,2A Temp Controller in Mini Instrument format with LED temperature display WTC3293-14001
€552.00*
The WTC3293-14001 is a mini-instrument temperature controller with a temperature (not resistance) display and onboard adjustments.Wrapped around the precision WTC3243 temperature controller, it is configured for use with a TCS610 thermistor. Wire your thermoelectric cooler and thermistor to the board with the cable provided. Add the appropriate DC power supply and indicate the input voltage on the jumper. With the output disabled, adjust the on-board 12-turn trimpot and watch the setpoint temperature change on the 4-digit display. Switch to Actual temperature and display your thermistor temperature. Watch the LED tree to see "over/under temperature" or "stable at setpoint" status. Enable the output current and watch the temperature quickly lock in on the setpoint.The green LED on the In-Range indicator lights when actual temperature is within 0.05°C of the setpoint. If the actual temperature exceeds the setpoint, the upper LED will light. If it is below the setpoint temperature, the lower LED will light.The WTC3293-14001 has been designed to work with various thermoelectrics driving up to ±2.2 Amps. It operates with +7 V, +9 V, or +12 V input voltage.
Key Features
Low noise, maximum temperature stability commercially available
Display thermistor temperature directly - no tables to convert resistance to temperature
LED indicator shows over temperature, stable at setpoint, or under temperature status
Adjust setpoint with a 12-turn potentiometer or an external voltage
Control temperature using a 10 k© thermistor
Fixed resistors set Proportional Gain, Integrator Time Constant, and thermoelectric current limits
Enable/Disable Output Current Switch
Includes Output Cable & DC Power Supply
Works with a wide range of thermoelectrics
Product number:
C008984-6
Manufacturer:
Only 2 available
2,2A Temp Controller WHY5640
€126.50*
The WHY5640 is a general purpose, low cost, analog PI (Proportional, Integral) control loop for use in thermoelectric or resistive heater temperature control applications. The WHY5640 maintains precision temperature regulation using an active resistor bridge circuit that operates directly with thermistors or RTD temperature sensors. Supply up to 2.2 Amps of heat and cool current to your thermoelectric from a single power supply. Accessories include a heatsink WHS302, thermal washer WTW002, and fans WXC303 (5 V), WXC304 (12 V), and an evaluation board WHY5690. Connect two or more WHY5640 units together and drive higher output currents. A single resistor or trimpot sets the temperature setpoint. Independent heat and cool current limits are set by single resistors. A single resistor sets proportional gain. A resistor / capacitor in series sets the integrator time constant.
Key Features
+5 to +26 V Control Electronics Supply
+4.5 to +30 V Power Drive Supply
Low Cost
0.008 C Stability (typical)
PI Temperature Control
High ±2.2 Amps Output Current
Control Above and Below Ambient
Small Package Size
Product number:
C008960-6
Manufacturer:
2,2A Temp Controller WTC3243
€161.00*
The WTC3243 is a compact, analog PI (Proportional, Integral) control loop circuit optimized for use in ultrastable thermoelectric temperature control applications. It easily handles variable operating conditions with a stability of better than 0.0009 ºC. The temperature setpoint is set by a remote voltage signal. It is capable of controlling both thermoelectric and resistive heaters, and only five external resistors are needed to optimize the controller for your specific application. The WTC3293 Evaluation Board is available to quickly integrate the WTC3243 into your system and can be optimized for sensor type. Use the adjustable trimpots to configure heat and cool current limits, proportional gain, and integrator time constant.
The robust and reliable WTC3243 has been designed into electro-optical systems, airborne instrumentation, spectroscopic monitors, and medical diagnostic equipment. It is particularly well-suited to applications where temperature is scanned across ambient.
Key Features
Linear PI Control Stability of 0.0009°C
Heat and Cool Current Limits
Adjustable Sensor Bias Current
Drive ±2.2 A of TEC or Resistive Heater Current
Small Size of 1.3" X 1.28" X 0.313"
Supports Thermistors, RTDs, and IC Sensors
Single Supply Operation: +5 V to +30 V
14-pin DIP PCB Mount
Monitor Actual Temperature
Quickly and easily integrated with WTC3293 Evaluation Board
Product number:
C008964-6
Manufacturer:
2,5A Chassis Mount Temp Controller PTC2,5K-CH
€503.45*
The PTC-CH Series Chassis Mount Temperature Controllers deliver the precision performance and long-term reliability you expect from a Wavelength Electronics temperature controller. PTC-CH Series controllers are found in such diverse applications as particle and droplet measurement, manufacturing machine vision systems, biomolecular interaction analysis, and more.The PTC-CH controllers operate from a single power supply between 4.5 V and 30 V, and a selection of models allows you to optimize the current output level for your application. The linear bipolar controller drives a Peltier thermoelectric cooler or a resistive heater, and the chassis-mount package integrates easily into OEM applications. PTC-CH controllers interface with a variety of temperature sensors, and the bias current is adjustable in order to maximize controller sensitivity and stability for your application.The compact chassis-mount design simplifies heatsinking and requires minimal space. PTC-CH controllers are quick to configure for your prototype project, and there are no surprises when it's time to integrate the controller into the final design.Practical Features For Real-World Conditions
Built-in features make your product more robust to real-world operating conditions and minimize your electronics overhead:
If the optional remote temperature setpoint signal is lost, the controller defaults to a standard "safe" temperature setpoint (25ºC when a 10 k© thermistor is used). The safe temperature can be changed at the factory; call for details.
An on-board trimpot is used to set the output current limit to prevent over-driving the TEC, and helps protect your load from thermal runaway situations.
Proportional gain is easily adjusted with an on-board trimpot.
Low temperature coefficient design remains stable across a wide range of ambient conditions. When used with Wavelength's laser drivers, such as the PLD Series, these temperature controllers provide stable and reliable performance that sets your system apart from your competitors' and keeps your customers satisfied.
Key Features
Drive up to ±2.5, ±5.0, or ±10.0 A of linear bipolar TEC or heater current
Add a booster unit to drive up to ±20.0 A
Single supply operation: 5 to 30 VDC
Small package: 3.0" x 3.2" x 1.1"
Use a wide variety of temperature sensors
Remote Output and Setpoint controls
Short term stability: 0.0012°C
Selectable sensor bias current
Adjustable current limit
Failsafe Setpoint default in case of remote temperature setpoint signal error
Product number:
C008985-6
Manufacturer:
3A Temp Controller for 0,062" PCB HTC3000-62
€162.92*
The advanced and reliable circuitry of the HTC series achieves 0.0009°C temperature stability. Its small, low profile package is ideal for designs with space constraints. The linear, PI control loop offers maximum stability while the bipolar current source has been designed for higher efficiency.The HTC temperature controllers are easily configured for any design. Virtually any type of temperature sensor can be used with the HTC and a built in sensor bias current source simplifies use with resistive temperature sensors. The independently adjustable Proportional Gain (P) and Integrator Time Constant (I) can be modified to optimize temperature overshoot and stability.Other features offer added flexibility. A single resistor sets the maximum output current to your load. Add a diode to operate resistive heaters with a unipolar output current. An onboard reference voltage simplifies potentiometer control of the temperature setpoint. You can also choose to operate remotely with an external setpoint voltage. Two monitor pins provide access to the temperature setpoint voltage and the actual sensor voltage.
Key Features
Compact Size - 1.5 and 3.0 A Models
Interfaces with Thermistors, IC Sensors, & RTDs
Single supply operation +5 V to +12 VDC (contact factory for higher voltage operation)
+11 V compliance with +12 V input
Stabilities as low as 0.0009°C
Temperature Setpoint, Output Current Limit, Sensor Bias, Proportional Gain, and Integrator Time Constant are User Adjustable
Monitor outputs for Temperature Setpoint and Actual Temperature
Linear Bipolar or Unipolar Output operates thermoelectrics or resistive heaters
Product number:
C008994-6
Manufacturer:
3A Temp Controller for 0,031" PCB HTC3000
€162.92*
The advanced and reliable circuitry of the HTC series achieves 0.0009°C temperature stability. Its small, low profi le package is ideal for designs with space constraints. The linear, PI control loop offers maximum stability while the bipolar current source has been designed for higher efficiency.
The HTC temperature controllers are easily configured for any design. Virtually any type of temperature sensor can be used with the HTC and a built in sensor bias current source simplifies use with resistive temperature sensors. The independently adjustable Proportional Gain (P) and Integrator Time Constant (I) can be modifi ed to optimize temperature overshoot and stability.
Other features offer added flexibility. A single resistor sets the maximum output current to your load. Add a diode to operate resistive heaters with a unipolar output current. An onboard reference voltage simplifi es potentiometer control of the temperature setpoint. You can also choose to operate remotely with an external setpoint voltage. Two monitor pins provide access to the temperature setpoint voltage and the actual sensor voltage.
Key Features
Compact Size - 1.5 and 3.0 A Models
Interfaces with Thermistors, IC Sensors, & RTDs
Single supply operation +5 V to +12 VDC (contact factory for higher voltage operation)
+11 V compliance with +12 V input
Stabilities as low as 0.0009°C
Temperature Setpoint, Output Current Limit, Sensor Bias, Proportional Gain, and Integrator Time Constant are User Adjustable
Monitor outputs for Temperature Setpoint andActual Temperature
Linear Bipolar or Unipolar Output operates thermoelectrics or resistive heaters
Product number:
C008980-6
Manufacturer:
4A Temp Controller for 0,062" PCB HTC4000-62
€193.87*
The advanced and reliable circuitry of the HTC Series achieves 0.0009°C temperature stability. Its small, low profile package is ideal for designs with space constraints. The linear, PI control loop offers maximum stability while the bipolar current source has been designed for higher efficiency.The HTC Temperature Controllers are easily configured for any design. Virtually any type of temperature sensor can be used with the HTC and a built in sensor bias current source simplifies use with resistive temperature sensors. The independently adjustable Proportional Gain (P) and Integrator Time Constant (I) can be modified to optimize temperature overshoot and stability.
Other features offer added flexibility. A single resistor sets the maximum output current to your load. An onboard reference voltage simplifies potentiometer control of the temperature setpoint. You can also choose to operate remotely with an external setpoint voltage. Two monitor pins provide access to the temperature setpoint voltage and the actual sensor voltage.
Key Features
Compact Size
±4.0 A Output
Interfaces with Thermistors, IC Sensors, & RTDs
Single supply operation +5 V to +12 V
+10.8 V compliance with +12 V input
Stabilities as low as 0.0009°C
Temperature Setpoint, Output Current Limit, Sensor Bias, Proportional Gain, and Integrator Time Constant are User Adjustable
Monitor outputs for Temperature Setpoint and Actual Temperature
Linear Bipolar Output operates thermoelectrics
Product number:
C009000-6
Manufacturer: