FOCP-1 Field Polishing Kit

Max. No. of Connectors 48; Connector Type ST, FC, SC, APC, MTP, SMA, E2000, Other; Radius of Curvature 7-30 mm; Apex Offset <50 µm; Undercut/Protrusion <50 nm; Back Reflection -35—65 dB; Automated Fiber Stub Removal Nanometer Technologies’ ACP-24 is an automated connector polisher with touchscreen technology for easy use and includes an ASR automated stub removal fiber optic polisher. The ACP-24 can polish many types of industry-standard, military and custom connectors. The system easily accommodates a full range of industry standard polishing styles to accommodate single mode polish specs like PC, UPC, APC, FLAT, and DOMED. With the ACP-24 you can automate fiber stub removal, polishing times, pressure and motor speeds for each step. Complete polishing procedures are stored inside of the ACP-24 to save time and ensure repeatability. Create, save, and recall custom polishing procedures for custom jobs. Polishing procedures can be saved to a computer for easy back-up or for transferring to another ACP-24. The ACP-24 utilizes Nanometer Technologies’ patented figure 8 polishing pattern that creates an angle of attack on the connector end face that changes 720°, 60 times a second, giving optimal control of the connector end face geometry. Use the ACP-24 to polish a wide variety of connectors including: ST, FC, SC, APC, MTP (up to 72 fibers), Mil 29504, Mil 38999, SMA, E2000, Radial Luxcis, T-Foca, bare fiber, bare plastic & many more. Polish a wide variety of ferrule material including all types of ceramic, glass, stainless steel, plastic, bare fiber, bare plastic, titanium & several others. The ACP-24 features a pneumatic pressure system, which allows for flexibility that is required to attain consistent accurate results The system is compatible with all MCP-24 polishing fixtures, supporting up to 48 connectors at a time. It includes the ASR System for automated stub removal – no more removing fiber stubs by hand. ASR works with Nanometer Technologies' polishing fixtures reducing the need to purchase special fixture plates and includes built-in pre-programmed processes. Key Features: Change Polishing Times, Pressure and Motor Speed Automated Fiber Stub Removal Easily Create and Save Custom Polishing Procedures Factory-preset Polishing Procedures Touchscreen Interface for Easy Use, Touchscreen is Both Water and Chemical Proof Patented Figure 8 Polishing Pattern Designed for High-volume Single Mode (SM) and Multi Mode (MM) Polishing Consistent High-yield Repeatable Performance Works With Existing MCP24 Fixture Radius of Curvature: 7 to 30 mm Apex Offset: <50 µm Undercut/Protrusion: <50 nm Back Reflection: PC -45 dB, UPC -55 dB, APC -65 dB, Multi Mode -35 dB Maximum Connector Load: 48 Dimensions: 368 x 375 x 356 mm Weight: 16.9 kg Applications: High-volume Polishing of Single Mode (SM) and Multi Mode (MM) Fiber Optical

Max. No. of Connectors 96; Connector Type ST, FC, SC, APC, MTP, SMA, E2000, Other; Radius of Curvature 7-30 mm; Apex Offset <50 µm; Undercut/Protrusion <50 nm; Back Reflection -35—65 dB; Automated Fiber Stub Removal Nanometer Technologies’ ACP-24/96 is an automated connector polisher with touchscreen technology for easy use and includes an ASR automated stub removal fiber optic polisher. The ACP-24/96 can polish many types of industry-standard, military and custom connectors. With the ACP-24/96 you can automate polishing times, pressure and motor speeds for each step. Complete polishing procedures are stored inside of the ACP-24/96 to save time and ensure repeatability. Create, save, and recall custom polishing procedures for custom jobs. Polishing procedures can be saved to a computer for easy back-up or for transferring to another ACP-24/96. The ACP-24/96 utilizes Nanometer Technologies’ patented figure 8 polishing pattern that creates an angle of attack on the connector end face that changes 720°, 60 times a second, giving optimal connector end face geometry. The system is compatible with all MCP-24 and MCP-48 polishing fixtures, supporting up to 96 connectors at a time. It includes the ASR system for automated stub removal – no more removing fiber stubs by hand. ASR works with Nanometer Technologies' polishing fixtures reducing the need to purchase special fixture plates. Key Features: Polish 96 LC Connectors at a Time Polish 24 MT Connectors at a Time ASR Automated Fiber Stub Removal Automatically Removes 96 Fiber Stubs in 1 min Change Polishing Times, Pressure and Motor Speed 30 Factory-preset Polishing Recipes for All Types of Connectors Easily Create and Save Custom Polishing Procedures Accurate Control of Pressure, Speed and Time 7” Touchscreen Interface for Easy Use, Touchscreen is Both Water and Chemical Proof Patented Figure 8 Polishing Pattern Designed for High-volume Single Mode (SM) and Multi Mode (MM) Polishing Consistent High-yield Repeatable Performance Works With Existing MCP24 & MCP 48 Fixtures Radius of Curvature: 7 to 30 mm Apex Offset: <50 µm Undercut/Protrusion: <50 nm Back Reflection: PC -45 dB, UPC -55 dB, APC -65 dB, Multi Mode -35 dB Maximum Connector Load: 96 Dimensions: 368 x 375 x 356 mm Weight: 16.9 kg Applications: High-volume Polishing of Single Mode (SM) and Multi Mode (MM) Fiber Optical

Connector Type All; No. of Connectors 24; Process Time <35 s; Programmable RPM Ramp Generator; Dimensions 368x191x191 mm The ASR-24 fiber stub removal system features an automatic stub removal process exclusively from Nanometer Technologies. This process will remove the fiber stub from the connector end face in a seamless process, 24 at a time, in under 35 s. Instead of doing all fiber stub removal by hand, grinding down the fiber stub one by one for each connector, ASR-24 allows you to remove the fiber stub from up to 24 connectors in 35 s or less – a serious decrease in time and labor for this process. The ASR-24 not only removes the fiber stubs and epoxy, it will also help streamline and shorten your polishing processes on your polisher. You can be sure all the connectors are the same length when put into your polisher for polishing. Key Features: Remove 24 Fiber Stubs at a Time Less Than 35 s for Removing 24 Fiber Stubs (Minus Load Time) Touchscreen Technology for Easy Use Programmable RPM Ramp Generator for Controlling Motor Speed Available for All Connector Types No More Removing Fiber Stubs by Hand Dimensions: 368 x 191 x 191 mm Weight: 4.5 kg Applications: Removing up to 24 Fiber Stubs from Fiber Optical Connectors in One Process Step

FC/PC; stainless steel     When hand polishing fiber optic connectors, you can't afford to leave anything to chance.  These Fiber Optic Hand Polishing Discs, or hockey pucks as some installers call them, enable you to achieve quality endface finishes and consistent results time after time.  

FC/APC; stainless steel     When hand polishing fiber optic connectors, you can't afford to leave anything to chance.  These Fiber Optic Hand Polishing Discs, or hockey pucks as some installers call them, enable you to achieve quality endface finishes and consistent results time after time.  

SMA 905/906; stainless steel When hand polishing fiber optic connectors, you can't afford to leave anything to chance.  These Fiber Optic Hand Polishing Discs, or hockey pucks as some installers call them, enable you to achieve quality endface finishes and consistent results time after time.  

ST/SC/FC; stainless steel When hand polishing fiber optic connectors, you can't afford to leave anything to chance.  These Fiber Optic Hand Polishing Discs, or hockey pucks as some installers call them, enable you to achieve quality endface finishes and consistent results time after time.  

SC/APC; stainless steel When hand polishing fiber optic connectors, you can't afford to leave anything to chance.  These Fiber Optic Hand Polishing Discs, or hockey pucks as some installers call them, enable you to achieve quality endface finishes and consistent results time after time.  

SC/PC; stainless steel  When hand polishing fiber optic connectors, you can't afford to leave anything to chance.  These Fiber Optic Hand Polishing Discs, or hockey pucks as some installers call them, enable you to achieve quality endface finishes and consistent results time after time.  

MU/LC; stainless steel When hand polishing fiber optic connectors, you can't afford to leave anything to chance.  These Fiber Optic Hand Polishing Discs, or hockey pucks as some installers call them, enable you to achieve quality endface finishes and consistent results time after time.  

All Necessary Tools Included; Special Version for PM Connectors Available; Sturdy Aluminium Case; Weight 7.3 kg OZ Optics’ comprehensive fiber optic termination kits include all of the tools necessary to make field terminations of fibers with commercially available connectors. The kits come in a sturdy, dent-proof aluminium case, providing easy transport with rugged protection. The total weight of the kits is 7.3 kg. The kits contain enough consumable supplies to process about 100 connectors. The consumable supplies may be ordered separately. A special version of the termination kit is available for polarization maintaining (PM) connectors. This kit includes special low-shrinkage epoxies to minimize stresses on the fibers. The epoxy is available as a separate item. The kits include the following tools: Five 230 mm by 330 mm, 5 µm Grit Polishing Film Five 230 mm by 330 mm, 1 µm Grit Polishing Film Ten 230 mm by 330 mm, 0.3 µm Grit Polishing Film 100X Microscope With a Connector Adapter Five Packs of Two-Component Epoxy Three Sizes of Buffer Tube Strippers Screwdriver With Four Bits Glass Polishing Plate Diamond Pen Scribe Index Matching Gel Polishing Disc T-Type Stripper Cotton Swabs Crimping Tool Epoxy Mixer & Pad Utility Knife Kim Wipes Scissors Tape Fiber Cleaner Tweezers Folding Knife Cable Stripper In addition, a number of accessories are available for the kit that may be ordered separately. A connector heater is available for curing the epoxy used in the terminating kit. The heater can handle 24 connectors at once and ensures even curing. A heat gun for curing epoxy and to shrink heat shrink tubing is also available. Key Features: All Necessary Tools Included to Make Field Terminations of Fibers With Connectors Special Version for Polarization Maintaining (PM) Connectors Available Various Additional Accessories Available Sturdy, Dent-proof Aluminium Case Weight: 7.3 kg Applications: Field Termination of Fibers With Commercially Available Fiber Optic Connectors

Max. No. of Connectors 12; Connector Type FC, SC, ST,FDDI, E2000PC, 2.5 mm, Other; Radius of Curvature 7-30 mm; Apex Offset <50 µm; Undercut/Protrusion <50 nm; Back Reflection -35—65 dB With the ability to polish up to 12 connectors at once and control the polishing process on every level, Nanometer Technologies’ versatile MCP-12 mass connector polisher is the perfect solution to your high-quality connector polishing needs. Fixture plates for the MCP-12 are designed to reduce consumable waste saving money and film. The MCP-12 mass connector polisher features consistent and repeatable processes. The device easily meets the industry-level standards for polishing including the specifications for TIA, IEC/Bellcore and GR326. Nanometer Technologies’ patented figure 8 polishing system allows the user to tightly control radius, apex offset and fiber height. MCP-12 mass connector polishers can polish a wide range of industry standard, military and custom connectors and accommodate a full range of industry standard polishing styles including PC, UPC, 8 DEG APC, 10 DEG APC, FLAT, SPHERICAL, RADIUS and DOMED. The MCP-12 can also polish a wide variety of ferrule material including ceramic, glass, stainless steel and plastic. Nanometer Technologies’ universal polishing fixture accommodates FC, SC, ST,FDDI, E2000PC and most 2.5 mm ferrules, thus reducing the need for several different polishing fixtures. The MCP-12 is very easy to use, desired results can be achieved with minimal training by even the most inexperienced user. Every MCP-12 polisher comes with a detailed training CD to familiarize technicians with the polishing methods. Key Features: Polish 4 to 12 Connectors at a Time Designed for High-Quality Single Mode (SM) and Multi Mode (MM) Polishing Figure 8 Polishing Pattern: Exclusive Patent Design Utilizes the original polish methods which tightly controls the radius, apex offset and fiber undercut. Universal Fixture Plate: Accommodates FC, SC, ST, FDDI, E2000PC and 2.5mm Ferrules Versatility: Easily Accommodates a Full Range of Industry-standard Polishing Styles: UPC, 8 DEG APC, 10 DEG APC, FLAT, SPHERICAL, RADIUS and DOMED Polishes a Wide Variety of Ferrule Material Including: Ceramic, Glass, Stainless Steel and Plastic Every MCP-12 Polisher Comes With an Easy-to-follow Training CD Polish to Industry-level Standards: TIA, IEC/Bellcore, GR326 Reduce Consumables Cost Increase Production Consistent Repeatable Performance Pneumatic Pressure Control Quickload Universal Polishing Plate™ APC and Custom Plates Available Polish 1,500+ Connectors to Bell Core Specs Per Day, Consistently Using Two UNI-32 Fixtures Radius of Curvature: 7 to 30 mm Apex Offset: <50 µm Undercut/Protrusion: <50 nm Back Reflection: PC -45 dB, UPC -55 dB, APC -65 dB, Multi Mode -35 dB Maximum Connector Load: 12 Dimensions: 305 x 305 x 152 mm Weight: 9.6 kg CE-certified Units Available Application: High-volume Polishing of Single Mode (SM) and Multi Mode (MM) Fiber Optical Connectors (PC, UPC, APC, Other); High-volume Polishing of Industry-standard, Military and Custom Fiber Optical Connectors