CP10G02 Aluminum Cold Plate with 2-Pass Copper tube, beaded fittings

Press-Lock Technology; Thermal Performance 0.004 to 0.059 °C/W; Max. Pressure 10 bar; Max. Flow Rate 4, 8 l/min; Straight Fittings Lytron’s CP10/CP12/CP15 series of standard tubed cold plates provide cost-effective thermal solutions for component cooling applications where the heat load is low-to-moderate. These tubed cold plates consist of copper or stainless steel tubes pressed into a channeled aluminum extrusion. The CP10/CP12/CP15 series of tubed cold plates is manufactured using Lytron’s proprietary Press-Lock technology, which mechanically locks the tubes into the aluminum plate. Press-Lock technology eliminates the need for performance-limiting epoxy between the tube and the plate, resulting in superior thermal performance. Compared to similar tubed cold plates, the CP12 cold plate offers 30% better performance and the CP15 offers 40% to 50% better performance. Copper tubes are compatible with water and most other common coolants, while stainless steel tubes (CP10 only) can be used with deionized water or corrosive fluids. Each tubed cold plate has a single tube with no joint, ensuring leak-free operation. The tubes of the CP12 and CP15 cold plates are coplanar with the plate to allow for dual-sided mounting. The cold plate's tube side offers higher performance as the copper tubes are in direct contact with the component being cooled. CP10 models are available with 9.5 mm copper and stainless steel tubes in 2-pass or 4-pass configuration for single-sided mounting. CP12 models are available with 9.5 mm copper tubes in 4-pass configuration for dual-sided mounting. CP15 models are available with 6.4 mm copper tubes in 6-pass configuration for dual-sided mounting. If you can’t find a tubed cold plate that meets your requirements, please get in touch with the AMS Technologies thermal technology experts to discuss your customized solution! Key Features: Thermal Performance: 0.004 to 0.059 °C/W @ 7.6 l/min (3.8 l/min for CP15) Fluid Compatibility: Water, Common Coolants (Copper Tubes); Deionized Water, Corrosive Fluids (Stainless Steel Tubes) Configuration: 2-pass (CP 10), 4-pass (CP10, CP12), 6-pass (CP15) Mounting Surface: Single Sided (CP 10), Double Sided (CP12, CP15) Tube Diameter: 9.5 mm (CP10, CP12), 6.4 mm (CP15) Fitting: Straight Plate Material: Aluminium Maximum Pressure: 10 bar Maximum Flow Rate: 8 l/min, 4 l/min (CP 15) Applications: Component Cooling Where the Heat Load is Low-to-moderate

UV-NIR; 365-980 nm; 0.84-15 W; Iop 350-3,500 mA; Vop 1.4-15.5 V; Typ. Output Power 30-1,500 mW Mightex’s high-power LCS-Series of collimated LED light sources employ a high-NA (numerical aperture) aspherical collimating lens for precision collimation and high light throughput. Four mechanically differing sub-series with clear apertures of 11, 22, 38 and 48 mm are available. A LED collimator consists of a collimating lens and a LED emitter. The LED emitter is placed at the focal plane of the collimating lens. The collimating lens thus images the LED emitter into infinity. LED collimators can be used as the light source in an illumination system. For example, LED collimators can replace the standard lamp assembly in a microscope to provide stable, intense, and fast-modulated illumination. Typically, the rest of the illumination optics will image the LED emitter onto the pupil of the imaging optics whereas the lens aperture on the collimator where intensity is uniform will be projected onto the object. In other illumination applications, similar arrangement should be made to produce uniform and efficient illumination. The LED emitters of the high-power LCS-Series collimated LED light sources are mounted directly onto the metal base of the collimator which also features an integrated heat sink. This configuration minimizes thermal resistance between the LED emitter and the heat sink resulting in better heat dissipation. The collimating lens can be adjusted if needed for precise collimation. A locking ring fixes the lens position after adjustment. The collimators have been pre-adjusted in the factory. Multi-chip LED emitters (i.e. Type-B) have been added to the high-power LCS-Series product portfolio. Some of these 7 W to 15 W LEDs have total optical power exceeding 1 W, quadrupling the power of a single-chip LED. Such Type-B models with higher powers (7 W and higher) feature a cooling fan and have a different form factor compared to other models. Please examine the installation drawings carefully. Power supply for the cooling fan is included in the price of the Type-B LCS-Series of collimated LED light sources. The LED collimators include a 1.5-meter cable with two bare-wire terminals at the end for universal LED controllers. Models with 22 or 48 mm clear aperture are also available connectorized for Mightex BLS-Series LED controllers. The light sources can be driven by Mightex LED controllers or other LED controllers and current sources. An optional focusing module can be mounted on the front of the LED collimator to focus light into a tight spot which is an image of the LED emitter. One of the applications with the focusing module is coupling LED light into a fiber or a lightguide. Additional interchangeable collimating lenses are available to produce different beam sizes with the same light source. Key Features: Interchangeable Aspherical Collimating Lens High Numerical Aperture (NA) High-power Emitters (up to 50 W) Wide Range of Available Wavelengths: 365 to 980 nm, 3000 to 6500 K for White LED Versions High Typical Collimated Output Power: 30 to 1,500 mW Adjustable Focus Optional Focusing Module Optional Lightguide Adapter Multiple Mounting Features for Lab and OEM Applications Integrated Heatsink Cooling Fan for >7 W Models Applications: Microscope Illuminator; General Purpose Light Source; Fiber Coupling (With Optional Focusing Module)